TechniSat DigiPal 2 manual Updating Software, Copying settings

Page 45

>Use the arrow keys left/right to select Yes or Abort.

>Confirm your selection by pressing OK.

8.5.3 Updating Software

You also have the facility of updating the operating software of your digital receiver.

>Press OK to display the sub-menu Software upda- te (Fig. 8-21).

To perform a software update, mark the line

Software update.

>Set the software update function to on by pressing

OK.

>In the line Update time, use the numeric keys to set the time when the software update is to be carried out.

>To initiate the update for the operating software manu- ally, press the red function key Test.

>Press the Menu key to return to normal operation. Should the parameters of the data used to download the soft ware update have changed, you can correct these via the menu. Current transmission data can be obtained via your retailer. Under normal cicumstances, there should be no need for you to make any changes in this menu.

Note:

For the new software version to be downloaded automatically, the digital receiver must be in standby mode. The downloading procedure is indicated by “TErL”, followed by “TEr0” to “TEr9” in the display. Ensure that this procedure is not interrupted by switching the receiver on or off while the download is in progress.

Independent of whether you have switched the automatic software update function on or off, the receiver will check automatically each time it is switched on whether a new ver- sion of the operating software for your digital receiver is avai- lable. If a new version of the operating software is available, this will be indicated by a message displayed on screen.

To start the software update, follow the instructions displayed on your screen.

8.5.4 Copying settings

You have the facility to copy all the settings of the program- me list, antenna settings, etc. of your digital receiver from your receiver to another digital receiver of the same type, and using the same operating software version. (Fig. 8-22)

>Use a null modem cable to connect the two receivers.

>Switch on the receiver to which the settings are to be transferred.

(Fig. 8-21)

(Fig. 8-22)

45

Image 45
Contents DigiPal Contents Page Page Illustrations Remote ControlVCR Page Important notes on operation Please read this firstWhen not in use Safety notesVCR Antenna ConnectionsConnection to a television set Video cassette recorder VCRMains power connection Getting started initial installationHi-fi amplifier Serial interface RSMenu/OSD language Exiting from the installation assistant Basic settings SettingsMenu language Time difference to GMT hoursCountry Remote control codeAntenna feed Stand-by clockLanguage Audio signal Audio/Video settingsTV Scart mode VCR Scart modeSwitching on and off Antenna adjustmentOperation Dolby Digital AC3Using the numeric keys Using the Programme up/down keysUsing the programme list Navigator Programme selectionSelecting a list Calling up blocked programmesInformation box Volume control Dolby Digital AC3 modeSelecting a different language Return to last programme selected TV/Radio switchingDisplay time and programme information Additional Programme informationChannel information Sleep timerFreeze frame Video textSub-titles Electronic Programme Guide SFI Downloading SFI dataInterrupting the download Now Table of current programme contents Viewing the Electronic Programme GuideNext SFI Functions MoreSFI Information Marking a programmeSFI Programme overview SFI Timer programmingSFI overview by programme type catego Timer recording Manual timer programmingExiting SFI Page Changing timer programming Timer overviewDeleting timer programming Programming a new timer eventConfiguring the Favourites list Changing the basic programmingCalling up the Navigator Programme List Manager Adding programmes to the Favourites list Remove Programming the electronic programme guide Deleting from the Total listSorting programmes Please note Selecting a channelSFI Channel Start categoryChanging the receiver PIN code Parental controlblocking programmesSelecting a programme ModeAutomatic Scan Programme search scanChannel scan Expanded ScanAfter the scan Manual ScanService settings Activating default factory settingDelete all programmes Updating Software Copying settingsTechnical terms System configurationOSD Technical dataTV Scart BT.653-2 lines 6-22 Problem Possible cause Solution Trouble-shooting guidePage Page AC3 IndexProgramme selection Using the programme up/down keys Switching on and offUsing the programme list Volume control