Panasonic NV-FJ760 manual Link Function, Crystal View Control CVC, Pin Scart Socket

Page 57

Q Link Function

This function works only if the VCR is connected via a fully- wired 21-pin Scart cable to a TV featuring the Q Link or similar function.

Q Link offers the following functions:

(1)Download from the TV

When you connect the VCR to a TV, the station list data is automatically copied from the TV to the VCR, and the TV stations are assigned to the programme positions on the VCR in the same order as on the TV.

(2)Direct TV Recording

By simply pressing the DIRECT TV REC button 6, you can at once record the same programme that you are watching on the TV.

°(3) TV/VCR Auto Power On

Even if the TV and the VCR are off (standby mode), pressing the Play I, SHOW VIEW L or PROG./CHECK button < automatically turns on both the TV and the VCR.

When a cassette with a broken erasure prevention tab is in the VCR, it turns on and starts playback. The TV also turns on.

°(4) VCR Auto Power Off

When you turn the TV off, the VCR is turned off as well. However, this function only works during rewinding, in the stop mode, or when no cassette is inserted.

If the VCR receives the Auto Power Off command while it is rewinding the tape, it turns off after the rewinding has been finished.

This function does not work during the following operations:

Preset Download, Auto Setup, Auto Clock Setting and Manual Tuning.

°(5) On Screen Display Messages

When you are watching a TV programme, the following VCR messages appear on the TV screen to inform you of the VCR’s condition:

Message

Message appears when:

 

 

This programme has

A timer recording has just started.

already started

 

Set VCR to timer

The VCR is not in the timer standby

standby mode

mode 10 minutes before the

 

programmed recording start time of

 

a timer recording (message appears

 

every minute during these 10

 

minutes).

VCR is in timer

The VCR-ON/OFF 1, Play I,

standby mode

EJECT Z or LIBRARY button M

 

was pressed, although the VCR is in

 

the timer standby mode.

VCR is in timer

The VCR-ON/OFF 1, Stop 9, REC/

recording mode

OTR d, Pause/Still e (Pause/Slow

 

7), SHOW VIEW L , AUDIO ? or

 

SUBTITLE button O was pressed

 

while the VCR is in the timer

 

recording mode.

¡Depending on the type of TV used, the above messages may not appear correctly.

°The operations marked with asterisk are only available if the VCR is connected to a TV featuring

the Q Link or the DATA LOGIC function.

Note:

If “Power save” is set to “ON”, the Q Link functions do not work when the VCR is switched off (standby mode).

Crystal View Control (CVC)

The crystal view control function ensures that you always obtain the optimum picture quality so that you get the best picture automatically.

While the VCR is turned on, the CVC indication b is always displayed to show that the Crystal View Control is activated.

21-pin Scart Socket

The 21-pin Scart socket transmits both input and output signals for picture and sound. TVs equipped with the same type of socket can be connected here.

This type of socket is also called Peritel, Euro Connector and Euro AV.

13 5 7 9 11 13 15 17 19 21

2 4 6 8 10 12 14 16 18 20

AV1 Scart Socket (for Q Link connection)

1

Audio output CH2 (R)

12

No connection

 

2

Audio input CH2 (R)

13

Red ground

 

3

Audio output CH1 (L)

14

Blanking ground

 

4

Audio ground

15

Red

 

5

Blue ground

16

Blanking

 

6

Audio input CH1 (L)

17

Video output ground

 

7

Blue

18

Video input ground

 

8

Switching voltage

19

Video output

 

9

Green ground

20

Video input

 

10

Q Link data

21

Ground

 

11

Green

 

 

 

AV2 Scart Socket

 

 

 

1

Audio output CH2 (R)

12

Reserved

 

2

Audio input CH2 (R)

13

Red ground

 

3

Audio output CH1 (L)

14

Blanking ground

 

4

Audio ground

15

Red

 

5

Blue ground

16

Blanking

 

6

Audio input CH1 (L)

17

Video output ground

 

7

Blue

18

Video input ground

 

8

Switching voltage

19

Video output

 

9

Green ground

20

Video input

Hints

10

Control signal

21

Ground

 

11

Green

 

 

Helpful

The Red, Green and Blue (RGB) video signals are looped

 

through only from an external source unit, for example from a connected a pay-TV decoder, i.e. they are not from tape playback.

57

Image 57
Contents NV-FJ760 Series Dear Customer ContentsSee page 4. VCR Operation See page 8. TV Operation Controls and ComponentsVCR Operation Checking the Accessories/Preparing the Remote Control UseBefore Keep the VCR away from high temperatures Avoid sudden changes in temperatureCleaning the VCR Avoid humidity and dustBefore Use Do not Remove Outer CoverRemarks Setting the Remote Control to Operate Your TV 3 Methods for Switching To the AV Input onYour Panasonic TVTV Operation Manufacturer Code List of TVs Compatible With the VCR’s Remote ControlHints Connecting SettingSteps below. RF Connection Or MethodAuto Setup Function Connecting and Setting UpScreen, the tuning is Complete Initial setting is channelNumber of the RF output Channel appears on the VCR Display SeeSetting Up When You Insert a Video CassetteTo Play back S-VHS Cassette Tape SQPB=S-VHS Quasi Playback PlaybackTo Eject the Video Cassette Using the Remote Control To Stop Playback Automatically Playback Off Timer FunctionPlayback To Play Back a Recorded Part RepeatedlyTo Select the Desired Tape Speed RecordingTo Pause Recording To Display the Approximate Remaining Tape TimeLinked Timer Recordings with a Digital Receiver To Prevent Accidental Erasure of Recorded ContentsRecording To Manually Adjust the Audio Recording Level Timer Recording To Programme with the On Screen Display OSDMode To Suspend the Timer Recording Standby Mode To Programme with ShowView FunctionPress the Numeric buttons To enter the ShowView number Timer Other Timer Recordings and Convenient FunctionsSetting the Recording Date/Days To Activate the Auto SP/LP Change FunctionProgramming a Timer Recording of a Satellite Programme To Check the Contents of Timer Recording ProgrammingsTo Change a Timer Recording Programming Timer Recording To Cancel the Programming of a Timer RecordingTo Check the Total Timer Recording Programming Time Precautions for Recording How to Read the Tape Library ContentsTape Library System To Check the Tape Library Data TapeTo Check on Which Cassette a Desired Programme Is Recorded Is found, the list of Library Contents menu disappearsPlayback starts By cassette number Press the Cursor buttons To selectTape Library System To Manually Enter or Editing a Title or CategoryMain menu Data are now deleted fromTo Demonstrate the Tape Library System To Restore Deleted Tape Library DataTo Cancel the Intro-Jet Scan or to Stop Playback To Cancel the Index Search or to Stop PlaybackSearch Functions OperationEditing Assemble EditingAdvanced Operations Album Function To Change the Recording TimePress the Still Album Button @ on the remote See page 20.Operations Advanced Synchronized EditingInsert Editing Audio Dubbing General Audio Dubbing on a Panasonic Hi-Fi VCRVW-EC500E/EC310E/EC300E to the Edit socket One-Touch EditingTV Mode VCR ModeTo Connect the VCR to a Decoder To Connect the VCR to a Stereo AmplifierConnect the RF coaxial cable to the Aerial Output socket How to install the satellite receiverPreparation Standby Type Action To Prepare the Satellite ReceiverPress the Numeric buttons 2 to select the satellite channel To select SAT EnterProgramme position whose To select aTV station name is indicated To select the entryTo Preset Pay TV Stations To Obtain the Best Tuning ConditionTo Enter Newly Available TV Stations List of TV Reception ChannelsTo Change the Subtitle Teletext Page Number Subtitles To Change the Type of Video System Colour TV systemTo Change the Title Teletext Page Number Title Various SettingsCursor buttons 34 R to Select the correct TeletextFollow the operations below Desired TV stationTo Restart the Auto Setup To Return the VCR to the Shipping ConditionTo Restart the Download Setting the VCR’s Clock To Manually Adjust the ClockTo Activate the Automatic Time Correction Function Other Convenient Functions Various Settings Settings for the Main Menu Item DisplayFor Automatic Display of the Channel Power save and the entry field Selected Subtitle mode on orFor Power save in this order Subtitles and the presentlySettings for the Main Menu Item Functions VariousTo Set the Playback Picture Sharpness Sharper or Softer To Set the Remote Control Mode To Set the Audio Mode to Be Used During PlaybackTo Set for One-Touch Editing or Other Editing Modes Country Setting Language SettingGlossary VPS Video Programme System/ PDC Programme Delivery ControlNicam Broadcasting System NV-FJ760EC/ECM/ECY Series Link Function Crystal View Control CVCPin Scart Socket √ On Screen Display Messages Before Requesting Service√ The VCR Does Not Work Correctly √ Playback Does Not Work Properly√ Recording Is Not Possible or Does Not Work Properly √ The Remote Control Does Not Work Correctly√ The Satellite Receiver Cannot Be Controlled Correctly √ The Tape Library System Does Not Work CorrectlyIf the Still Picture Scrolls Up or Down V-Lock Adjustment Adjusting the Playback PicturePrecautions To Return to Auto TrackingSpecifications Central P.O. Box 288, Osaka 530-91, Japan