Panasonic NV-FJ604, NV-FJ606, NV-FJ610 manual Preparing the Remote Control, VCR Operation

Page 4

Preparing the Remote Control

VCR Operation

When you want to operate the VCR, set the VCR/TV switch N to “VCR”.

°2 Numeric buttons

To select the programme positions (1–99) of the VCR. Example:

9:9

19: 1 9

To enter a ShowView number.

To enter numbers for various settings.

°6 No function

Inserting Remote Control Batteries

1

1 Slide off the battery cover.

2

2 Insert the batteries with the polarity (+ and -) correctly

- aligned.

++

°= Tape Counter Reset button

To reset the tape counter (elapsed time) to “0:00.00”.

The tape counter is automatically reset to “0:00.00” when a video cassette is inserted.

°@ No function

°O Infra-red transmitter

3

-

3 Replace the battery cover.

°T Child Lock Function buttons

(Convenient function to prevent unauthorized use)

This function deactivates all buttons on the VCR and the remote control. Use this function, when you do not want other people to operate the VCR.

To Activate the Child Lock Function:

1Hold down the OK and the OFF (i) buttons T simultaneously until the “!" hold” indication appears in the VCR display.

If you press a button while the Child Lock function is on, the “!" hold” indication appears in the VCR display to inform you that no operation is possible.

VCR display

Indication when the Child Lock function is activated

To Cancel the Child Lock Function:

1Hold down the OK and the OFF (i) buttons T simultaneously until the “!" hold” indication disappears.

If you disconnect the power cable, the Child Lock function is automatically cancelled after the power backup time of approximately 60 minutes has elapsed.

°Z Cassette compartment

°[ Infra-red Remote Control Receiver window

°] VCR display

Notes for Battery Replacement:

The service life of the batteries is approximately 1 year. However, it varies considerably depending on the frequency of use.

When they are exhausted, replace them with two AA, UM3, or R6 size batteries.

When the batteries are exhausted, remove them immediately and dispose of them correctly.

Make sure that the batteries are inserted with the polarity (+ and -) correctly aligned.

Do not mix old battery with new battery.

Do not mix different battery types, i.e. Alkaline and Manganese.

Do not use rechargeable (Ni-Cd) batteries.

Do not heat or short-circuit the batteries.

When you do not use the remote control for a long time, take out the batteries and store them in a cool, dry place.

If the Sliding Cover of the Remote Control Becomes Detached

If the sliding cover of the remote control becomes detached accidentally, fit it securely in place by placing it on the top of the remote control at the position shown in the illustration below, and pushing it down until it clicks into position.

It is not possible to fit the sliding cover in place by pushing or sliding it on from the bottom end of the remote control.

CorrectWrong

4

Image 4
Contents NV-FJ610 Series NV-FJ606 Series NV-FJ604 Series Contents Dear CustomerControls and Components 8 GPreparing the Remote Control Inserting Remote Control BatteriesIf the Sliding Cover of the Remote Control Becomes Detached VCR OperationDo not Remove Outer Cover RemarksSetting the Remote Control to Operate Your TV TV OperationConnecting the VCR to a TV Or MethodAuto Setup Function HintSetting Playback Recording To Prevent Accidental Erasure of Recorded Contents Linked Timer Recordings with a Digital ReceiverTo Display the Approximate Remaining Tape Time To Suspend the Timer Recording Standby Mode Timer RecordingTo Programme with the On Screen Display OSD To Programme with ShowView Function Press the Numeric buttons To enter the ShowView numberSetting the Recording Date/Days Other Timer Recordings and Convenient FunctionsTo Check the Contents of Timer Recording Programmings To Check the Total Timer Recording Programming Time To Change a Timer Recording ProgrammingTo Cancel the Programming of a Timer Recording To Cancel the Index Search or to Stop Playback To Cancel the Intro-Jet Scan or to Stop PlaybackSearch Functions OperationEditing Assemble EditingVCR Mode TV ModeTo Connect the VCR to a Decoder To Connect the VCR to a Stereo Amplifier¡If your satellite Settings To Obtain the Best Tuning Condition To Preset Pay TV StationsTo Enter Newly Available TV Stations List of TV Reception ChannelsTo Change the Type of Video System Colour TV system PALTo Restart the Auto Setup To Return the VCR to the Shipping ConditionTo Manually Adjust the Clock Setting the VCR’s ClockTo Activate the AutomaticTime Correction Function Other Convenient Functions Various Settings Tape length indicatorSound mode during playback L/R Tape speed indicatorOFF Language Setting To select Functions thenGlossary VPS Video Programme System/ PDC Programme Delivery ControlCrystal View Control CVC Pin Scart SocketBefore Requesting Service √ On Screen Display Messages√ The VCR Does Not Work Correctly √ Playback Does Not Work Properly√ The Remote Control Does Not Work Correctly Adjusting the Playback Picture√ Recording Is Not Possible or Does Not Work Properly Avoid sudden changes in temperature Keep the VCR away from high temperaturesCleaning the VCR Avoid humidity and dustSpecifications