Panasonic NV-FJ604 To Connect the VCR to a Decoder, To Connect the VCR to a Stereo Amplifier

Page 19

Connecting the VCR to a Decoder/ Connecting the VCR to a Stereo Amplifier

To connect this VCR to a decoder or a stereo amplifier, make the connections shown in the illustration below.

For the connection to the TV, see page 7.

.

For details about the connection, also read the operating instructions of the decoder or stereo amplifier.

Be sure to keep the VCR, TV and decoder or stereo amplifier switched off until you have finished all connections.

For your safety, do not connect or handle the equipment with wet hands.

To Connect the VCR to a Decoder

Decoder here refers to the device used to decode scrambled broadcasts (Pay TV).

a

≥When you start playback on the VCR, the TV is automatically switched to the VCR mode. However, during playback, it is not possible to switch the TV back to the TV mode.

≥If a Pay TV station has been selected on the VCR when you switch to the TV mode, the picture on the TV is scrambled when you select a Pay TV station on the TV. In this case, either switch to the VCR mode or select the AV input on the TV.

Hint:

“RGB” means separate Red/Green/Blue colour signals. If you connect a TV equipped with RGB input capability to the AV1 socket ` on this VCR, and a decoder equipped with RGB output capability to the AV2 socket a, the TV can receive RGB signal input from the decoder via the VCR.

To Connect the VCR to a Stereo Amplifier

Decoder (not supplied)

1

Audio cable (not supplied)

1 b

2

 

 

21-pin Scart socket

To an AC mains socket

 

21-pin Scart cable

 

 

(not supplied)

1Connect a 21-pin Scart cable (not supplied) to the AV2 21-pin Scart socket a on the VCR and to the 21-pin Scart socket on the decoder.

2Connect the decoder’s mains lead to an AC mains socket.

3Set “AV2” to “DECODER”. For details, see page 27.

AV Link Function

If the VCR is connected to the TV via a 21-pin Scart cable, you can use AV LINK button A to switch the TV from normal TV reception over to the video playback channel (AV input) (and vice versa). In the VCR mode (when the VCR indication in the VCR display is lit), the TV is switched to the video playback channel (AV input). In the TV mode (when the VCR indication is not lit), the TV is switched to TV reception.

 

VCR

TV

VCR Mode

VCR indication

AV Input

 

is lit.

is selected.

 

 

 

TV Mode

VCR indication

TV reception

 

is not lit.

is selected.

≥When you press the MENU button S to display the menu on the TV screen, the TV is also automatically switched to the VCR mode, however, the VCR indication does not appear in this case.

Audio Input sockets

Stereo amplifier (not supplied)

2

To an AC mains socket

1Connect an Audio cable (not supplied) to the Audio Output sockets b on the VCR and to Audio Input sockets on the stereo amplifier.

2Connect the stereo amplifier’s mains lead to an AC mains socket.

Advanced Operations

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents NV-FJ610 Series NV-FJ606 Series NV-FJ604 Series Dear Customer Contents8 G Controls and ComponentsVCR Operation Preparing the Remote ControlInserting Remote Control Batteries If the Sliding Cover of the Remote Control Becomes DetachedRemarks Do not Remove Outer CoverTV Operation Setting the Remote Control to Operate Your TVOr Method Connecting the VCR to a TVHint Auto Setup FunctionSetting Playback Recording To Prevent Accidental Erasure of Recorded Contents Linked Timer Recordings with a Digital ReceiverTo Display the Approximate Remaining Tape Time To Suspend the Timer Recording Standby Mode Timer RecordingTo Programme with the On Screen Display OSD Press the Numeric buttons To enter the ShowView number To Programme with ShowView FunctionSetting the Recording Date/Days Other Timer Recordings and Convenient FunctionsTo Check the Contents of Timer Recording Programmings To Check the Total Timer Recording Programming Time To Change a Timer Recording ProgrammingTo Cancel the Programming of a Timer Recording Operation To Cancel the Index Search or to Stop PlaybackTo Cancel the Intro-Jet Scan or to Stop Playback Search FunctionsAssemble Editing EditingTo Connect the VCR to a Stereo Amplifier VCR ModeTV Mode To Connect the VCR to a Decoder¡If your satellite Settings List of TV Reception Channels To Obtain the Best Tuning ConditionTo Preset Pay TV Stations To Enter Newly Available TV StationsPAL To Change the Type of Video System Colour TV systemTo Return the VCR to the Shipping Condition To Restart the Auto SetupTo Manually Adjust the Clock Setting the VCR’s ClockTo Activate the AutomaticTime Correction Function Tape speed indicator Other Convenient Functions Various SettingsTape length indicator Sound mode during playback L/ROFF To select Functions then Language SettingVPS Video Programme System/ PDC Programme Delivery Control GlossaryPin Scart Socket Crystal View Control CVC√ Playback Does Not Work Properly Before Requesting Service√ On Screen Display Messages √ The VCR Does Not Work Correctly√ The Remote Control Does Not Work Correctly Adjusting the Playback Picture√ Recording Is Not Possible or Does Not Work Properly Avoid humidity and dust Avoid sudden changes in temperatureKeep the VCR away from high temperatures Cleaning the VCRSpecifications
Top Page Image Contents