Parker Hannifin 88-020292-01 A manual Agency Additional Steps User Must Take

Page 42

Regulatory Agencies

The E-AC Drive is designed to meet the requirements of global regulatory agencies.

The E-AC Drive has shown compliance with the regulatory agencies in the following list. The list also shows additional steps users must take to ensure compliance.

Agency

Additional Steps User Must Take

UL, cUL

No additional steps are required. (The E-AC Drive is UL recognized, as

 

shipped from the factory.)

CE (LVD)

Earth connection for drive and motor (if applicable), proper installation

CE (EMC)

Varistors, mains filter, EMC cabling, EMC ready motor, proper installation

Installation Instructions

Although the E-AC Drive is technically considered a motion control component and is therefore not within the scope of the European Union’s CE (Conformité Europé enne) directives, Compumotor has taken the initiative to provide its customers with easy to integrate motion control products that meet global require- ments.

The following constitutes what is typically required to install the E-AC Drive into a CE compliant system. Additional installation measures may be required at some locations. The machine builder has ultimate responsibility for machine compli- ance.

Low Voltage Directive (LVD) Installation Requirements:

•Drive safety earth conductor

•Motor safety earth

•Drive must be installed such that the hazardous live terminals (barrier strip) are not accessible under normal operation

Electromagnetic Compatibility (EMC) Installation Requirements:

•Product does not need to be placed within an enclosure

•Mains filter (see filter recommendations)

•Transient suppressors (mains surge test)

•EMC cabling, braided and bonded as specified below

•EMC ready motor, or motor with EMC installation information

•Additional installation hardware as shown in drawings in this appendix

Additional Steps to Ensure Compliance

To meet the requirements of regulatory agencies, you must follow the installation guidelines presented below.

EMC –Electromagnetic Compatibility Directive –89/336/EEC

In order to meet the requirements of the Electromagnetic Compatibility Directive 89/336/EEC, the entire system must comply: motor, drive, cabling, and peripher- als. The installation of the product must include the following items.

42

E-AC Drive Hardware Installation Guide Appendix B – Regulatory Compliance: UL and CE

Page 41 Page 43
Image 42
Page 41 Page 43
Contents AC Drive Hardware Installation Guide User Information Table of Contents AC Drive Hardware Installation Guide AC Drive Hardware Installation Guide Introduction IntroductionAC Drive -DESCRIPTION DIP SwitchesBlock Diagram of E-AC Drive System System ComponentsInputs & Outputs AC Drive -COMPATIBLE MotorsCompumotor Family of Products ANTI-RESONANCEAC Drive Hardware Installation Guide Introduction Installation What YOU should have Ship KIT PrecautionsInstallation Overview PartInstallation Procedure Component Locations AC Drive Hardware Installation GuideAutomatic Test Setup Automatic TestConnect AC Power Installation Select a MotorSPEED/TORQUE Curves Bearings Information Motor SpecificationsParameters Units Size 17 FrameMotor Dimensions Dimensions in inches mmPage Precautions Connect the Motor to the Drive -WIRINGMotor Connector Wired for Series Motor Current Connecting the Motor Series WiringMotor Connector Wired for Parallel Motor Current Connecting the Motor Parallel WiringSeries Versus Parallel -SUMMARY Default Settings SET DIP SwitchesDIP Switch Location and Settings Motor CurrentWaveform Drive ResolutionANTI-RESONANCE Disable Automatic TestConnect a Controller -INPUTS & Outputs Connecting a Compumotor ControllerDrive I/O Connector Step InputDirection Input Shutdown InputFault Output Reset InputDimensions E-AC Drive Mount the DriveEnvironmental Considerations Panel Layout Dimensions Panel LayoutMount the Motor Extending Motor Cables Motor Temperature & CoolingMotor Modifications Less than 100 ft m 100 -200 ft -60 m Motor TypeConnect the Motor to the Load -COUPLERS Misalignment ConditionConnect AC Power Apply PowerAC Input Connections Test the Installation Peak Power RatingsTest Procedure Troubleshooting AC Drive Hardware Installation Guide TroubleshootingOvertemperature Protection Troubleshooting BasicsDiagnostic Leds Protective CircuitsANTI-RESONANCE Disable Technical SupportShort Circuit Protection Product Return Procedure Using Non-Compumotor Motors Using NON-COMPUMOTOR Motors Wiring ConfigurationsLead Motor Lead Motor Labeling the Leads Terminal Connections Direction of Motor RotationNon-Compumotor Motor Connections Setting Motor Current NON-COMPUMOTOR Motors Lead MotorsPage Regulatory Compliance UL and CE Low Voltage Directive LVD Installation Requirements Electromagnetic Compatibility EMC Installation RequirementsAgency Additional Steps User Must Take EMC Cabling FilterCable Shielding Clamp TypePanel Mounting the E-AC Drive Page AC Drive Hardware Installation Guide Index IndexAC Drive Hardware Installation Guide Index
Top Page Image Contents