JVC HR-J268EU Quest Ions and Answers EN, Ä remain lit on the display panel. Is there Problem?

Page 47

QUESTIONSANDANSWERSEN47

PLAYBACK

RECORDING

Q. What happens if the end of the tape is reached during playback or search?

A. The tape is automatically rewound to the beginning.

Q. Can the video recorder indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.During search, slow, still and frame-by-frame playback, I can’t hear any audio. What’s the problem?

A.This is normal.

Q.When returning from multi-speed search to normal playback, the picture is disturbed. Should I be concerned about this?

A.No, it is normal.

Q.Noise bars appear during multi-speed search. What’s the problem?

A.This is normal.

Q.Other than preventing further recording, what effect does removing the Record Safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the video recorder can’t find the programme I want to see. Why not?

A.There may be index codes too close together.

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the beginning of the continuation of recording. Why does this happen?

A. This is normal. It reduces distortion at the pause and resume points.

Q. Can the video recorder indefinitely remain in the Record-Pause mode?

A. No. The video recorder goes to its Stop mode auto- matically after 5 minutes to protect the heads.

Q. What happens if the tape runs out during recording? A. The video recorder automatically rewinds it to the

beginning.

TIMER RECORDING

Q. "" and "ä" remain lit on the display panel. Is there

aproblem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I programme the timer while I’m watching a tape or a TV broadcast?

A.You won’t see the picture as it is replaced by the on- screen menu, but the audio from the programme or tape you’re viewing can be heard.

Q.Is it possible to timer-record a TV programme broadcast in 2000?

A.Yes, it is possible.

ATTENTION

This recorder contains microcomputers. External electronic noise or interference could cause malfunctioning. In such cases, switch the recorder off and unplug the mains power cord. Then plug it in again and turn the recorder on. Take out the cassette. After checking the cassette, operate the unit as usual.

Image 47

Contents HR-J468EU HR-J311EU HR-J268EU To HR-J311/268EU Owners Safety PrecautionsFor Italy To HR-J468EU OwnersConnect Recorder to Mains Check ContentsBasic Connections Situate RecorderInternational Telephone Country Code Auto Set UpIf you are referring to the front display panel If you are referring to the on-screen displayThis Language CodeVia an RF cable only RF connection Your TV to the Video Channel. Refer toENU Preset DownloadJust Clock on If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage Return to Normal Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display On-Screen DisplaysPower Save Mode NexTView Link Access Mode SET ScreenTV Auto Power On Link FunctionsColour SYSTEM, then press OK or # to select Colour System SetAbout Ntsc Playback Press %Þ to move the highlight bar pointer toStart Playback Basic PlaybackLoad a Cassette PointActivate HIGH-SPEED Search Playback FeaturesPlayback Return to Automatic Adjust TrackingOverride Automatic Tracking ManuallyPicture Control Select Picture Control SET ModeAuto SP→LP Timer appears only with the HR-J468EU Repeat PlaybackBasic Recording SET Counter Display Recording FeaturesReset Counter Select Channel to WatchPress Record on the recorder Engage ITR ModeInstant Timer Recording ITR SET Recording Duration#to set to on or OFF S.T. Picture SystemPreparation Or press Record on the recorder RecordingPlayback Timer Programming Press SP/LP Timer WarningSatellite Tuner Users Time Express Timer ProgrammingBefore performing Express Timer Programming Start TimeEngage RECORDER’S SET VPS/PDC ModeTimer Mode SET Tape Speed HR-J468EU onlyNext programmes Check, Cancel And Replace ProgrammesPress ä Timer Press Again to check More information. Each Time you pressOK or #to select either Auto SP→LP Timer HR-J468EU onlyAuto Timer For ExampleBefore performing the following steps Prog REC ModeAutomatic Satellite Programme Recording Edit From a Camcorder Start Source Player Input ModeEdit To Or From Another Video Recorder SET Recording DECK’SHR-J468EU HR-J311/268EU AV2 Select SettingRecorder Back of Recorder Connection To Satellite TunerSatellite Tuner Unit Back of TVSet AV2 Select to AV2. pg DecoderSET Tuner Connecting Using a DecoderSelect Input Mode Connect DecoderGuide Program Number Set Showview SetupNumber Enter Receiving Channel Position NumberLanguage of your choice Access Auto CH SETTuner Set Auto Channel SetView Confirmation Screen Perform Auto Channel SETStoring Channels Manually Press %Þ @ #until the item you want to move begins When Receiving a Scrambled BroadcastDelete a Channel Change Station Channel PositionSwitch Stations Access Manual Channel SET ScreenPerform Tuning Access ManualTV Station And ID List SET Date and Time Clock SetTurn the Recorder on Channel position to the number representing Default setting is OFF. Set as desired by pressingRecorder is preset to receive clock setting SET Just ClockSET RF Output System Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetIf you’re using the RF OUT connec- tion No power is applied to the recorderRemote control wont function Mains power cord is discon- nectedRoubleshooting Quest Ions and Answers EN Ä remain lit on the display panel. Is there Problem?EN Index Rear View VCR, TV Prog +/-,TV +/-, TV Muting Remote ControlIN/OUT x 1, IN/DECODER x Maximum recording timeRotary two-head herical scan Ex. Francais is selected for Belgium Auto Set Up referring to the display panel