JVC HR-J648EH, HR-J648E, HR-J448E, HR-J248E Video Channel Set, Access Video Channel SET Mode

Page 8

8ENINITIALSETTINGS(cont.)

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) – Go to "With RF Connection" below.

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection) – Go to "With AV Connection" on next page.

IMPORTANT:

Before performing the following steps, make sure the recorder's power is off and there is no cassette inserted in the recorder.

¢	¢
q

Á

1

PROG.+/–	STOP
TV

1 2 3

4 5 6

7/ 8 9

0 4

2

TV PROG.

1 3 Á

¦ 7 8

1	4	¢
	4	¢
	3

OK

TEST SIGNAL

The channel on which the screen to the left appear clearly in step 2 is your Video Channel.

With RF Connection

ACCESS VIDEO CHANNEL SET MODE

	Hold down STOP on the recorder until the display
1			panel shows the following.
1

2	SET VIDEO CHANNEL
	Set your TV to UHF channel 36.

	● If the two vertical white bars appear clearly on the
			screen as shown in the illustration at bottom left, go
			to step 3.
	● If the two vertical white bars do not appear clearly,
			press TV PROG.+ or – to set the video recorder to a
			vacant channel between 22 and 69 which is not
			occupied by any local station in your area.
		(Ex.) If channel 50 is available in your area

Then set your TV to UHF channel 50 and check if the two vertical white bars appear clearly on the screen; if so, go to step 3. If not, re-set the video recorder to another vacant channel and try again.

NOTES:

●If you set the video recorder to a channel which is occupied by a local station or has neighbouring channels that are occupied by local stations, the picture reception quality will be affected and some interference noise will appear on the TV screen. Be sure to select a vacant channel which has no broadcast on neighbouring channels.

●If you cannot obtain the two vertical white bars clearly with any channel between 22 and 69, consult your JVC dealer.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to the Video Channel.

Image 8

Contents HR-J648EH Hi-FiHR-J648E HR-J448E HR-J248E Safety Precautions For ItalyTo HR-J648E/J648EH/J448E Owners Do not place the recorderCheck Contents Installing Your NEW Record ER ENBasic Connections Situate RecorderAuto Set Up Turn on the RecorderSelect Country EN I Nitial Sett IngsPerform Auto SET UP Select LanguageIf you are referring to On-screen displayInitial Settings If both auto channel set and auto clock set have failedLanguage for the on-screen display Just ClockLanguage Access Video Channel SET Mode Exit Video Channel SET ModeEN Initial Settings Video Channel SetWith AV Connection Press TV PROG. until the display panel showsOUT Now the video channel is set to offGuide Program Number Set SetupMake List of Stored Station Names Channel Positions When Using a Satellite Tuner Enter Showview NumberConfirm Channel Position Number Close MenuBasic Playback Load a CassettePoint Start PlaybackPlayback Playback FeaturesActivate HIGH-SPEED Search Adjust Tracking Override Automatic TrackingManually Return to AutomaticTape Position Indicator Activate RepeatActivate Instant Review Repeat PlaybackMemory SET Counter MemoryActivate Counter Basic Recording Access Main Menu S.T. Picture SystemScreen Return to NormalPlayback With HR-J648E/J648EH/J448E13 3 ENABLE/DISABLE ON-SCREEN DisplayOn-Screen Displays Recording Features Reset CounterSelect Channel to Watch SET Counter DisplayType of Broadcast On-screen Display Being Received Stereo BilingualRegular Monaural None Nicam Stereo Nicam BilingualEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press Record on the recorderTimer Recording EN Timer RecordingSatellite Tuner Users Regular Timer Programming EN Timer RECORDINGcontEnter Channel Position Press TV PROG. +Access Programme Access Main Menu ScreenRevise Programme InformationPress Display or Start + again to return to normal display Timer WarningPDC/VPS Recording SET Recording DECK’S Input Mode Edit To Or From Another Video RecorderMake Connections Start Source PlayerHR-J448E/J248E PlayerRecorder Recorder PlayerSET RECORDER’S Input Mode Edit From a CamcorderStart Camcorder Start RecorderConnecting Using a Decoder Select Input ModeConnect Decoder SET TunerTuner SET Auto Channel SetPointer to your countrys Name, then press OK.SET Select Item Delete ChannelClose Confirmation Select NEW PositionSwitch Stations Access Manual CH. SETPerform Tuning Select NEW StationTV Station And ID List Clock SET PreparationMove the highlight bar pointer to Clock SET by Screen appearsSET Clock Automatically Return to Normal ScreenSET Date and Time SET Just ClockÄ remain lit on the display panel. Is there a problem? Questions and Answer S E NIf you are using the AV connection Set the TV to its AV modeSet the TV receiver to the Video ClearTimer Recording Timer againIndex @ SP/LP Button pg HR-J648E/J648EH/J448EDisplay Panel Installing Batteries How To Use EN IndexOperating JVC TVs PROG. +Rotary two-head helical scan SpecificationsMaximum recording time Auto Set Up completed International Telephone Country CodeLanguage Code Language Code