JVC HR-J795EK manual Choose a Programme, Set the Tape Speed, Start Recording

Page 18

18

basic features

Recording

TV signals being received by the recorder’s built in tuner can be recorded onto a video tape. You can ‘capture’ a TV programme using your VCR.

before you start

Turn the TV on

Tune the TV to your Video Channel or to its AV mode

Choose a blank cassette which has the record safety tab still in place

Record

Safety Tab

Load the cassette into the VCR (see page 14)

1 PROG	?				30 SEC
	ENTE
			R/EN
					TR
MENU			3	OK		EE
MENU	TV PR			OK
	TV PR		+
	TV
		TV/VCR	AUDIO		– –:– –
	1		2		3
						2
	4		5		6
	VPS/PDC	DAILY/QTDN. WEEKLY/HEBDO
	7		8		9
	0000	AUX				4
			0
	START	STOP	DATE		PR
	DEBUT	FIN	DATE		PR
		EXPRESS
	1 PROG	?			30 SEC
			ENTER/ENTREE
	MENU			3	OK
		TV PR		+
	T				+
	V
	–				TV
		TV PR		–

TE PR

Choose a Programme

There are two ways to select a preset position of the VCR.

method one Press PR +/– or the number keys on the Remote Control to select the channel that you wish to record.

method two Push the center part of the JOG Dial so that the preset position appears on the TV screen. While the display is shown, turn the JOG Dial to the right or left.

Set the Tape Speed

Press /• The current setting for the tape speed appears on the on-screen display or the VCR display panel for about 5 seconds. Press /again to change the setting while tape speed is displayed. You can choose Standard Play (SP) or Long Play (LP). The picture quality on LP recordings will not be as high as on SP recordings, but the tape will last longer.

Start Recording

There are two ways to start recording:

method one Press and hold Tand then press .on the Remote Control.

method two Press Ton the VCR.

When “DIRECT REC” is set to “ON” (☞pg. 35), if you press any button just after pressing Ton the VCR (or Tand .on the Remote Control), the recorder may not function properly.

Pause and Resume During Recording

On either the VCR or the Remote Control, press to temporarily stop recording and press .to resume. You cannot change the preset position on the VCR while it is recording but you can while it is paused (see Choose a Programme at the top of this page).

Image 18

Contents HR-J795EK Safety Precautions Blue to N Neutral or Black Brown to L Live or RedMoisture Condensation Some Do’s And Don’ts On The Safe Use Of EquipmentContents Front panel Diagram Key Front PanelWelcome to JVC Getting Everything ReadyPerform Auto Setup pg Auto Setup Three-Step Quick StartPreset Download Go straight to 2000 used as example only Check the ResultsFinish Off Perform Clock Set on Go to StepBasic Features Play PlaybackLoad a Video Cassette Stop & EjectVideo Heads Cleaning Rewind and Fast ForwardAdvanced JOG Dial Playback FeaturesPg , 24H Express Timer Programming pg , etc Pause During PlaybackSlow Motion Variable Speed SearchHigh Speed Search Set the Tape Speed RecordingChoose a Programme Start RecordingResetting the Counter Display Tape Remaining TimeChange Display Information Instant Timer Recording Recording Resume FunctionGet to the Video Plus + Screen Enter the PlusCode NumberPress p. You will see the following TV screen information Return to Normal Screen Engage Timer Mode Express Timer Programming Get to the Programme ScreenEnter Programme Details AUX 24H Express Timer Programming Check, Cancel & Change Programmes Press c, then press oto disengage the timer modeTimes as necessary Basic features Advanced Features Picture Quality Manual TrackingPicture Control B.E.S.T Picture System Recording and Playback Using B.E.S.TAvoiding B.E.S.T. Time Delay Turning B.E.S.T. on or OFFSound Modes Nicam Stereo and Bilingual BroadcastsSoundtrack Selection Index Search Finding Specific ScenesSkip Search Instant ReViewLink Functions TV Auto Power OnYou can use your TV’s Remote Control to turn off the VCR NexTView LinkDirect Rec Buttons. Press Or E to select on orRecording on Satellite Receiver Control Settings Installing Satellite ControllerAppropriate number keys to enter the brand Setting satellite receiver’s brandSET using the Aand Bbuttons. Press Or E ModeOr E to finish the Sat Control Set mode Check Result of TestPress the Aand Bbuttons to move Auto Satellite Auto Record from Satellite ReceiverAdvanced features Editing Using Another VCR EditingEditing from a Camcorder Start recorder Press TOther Functions On-Screen Display O.S.DPower Save Mode Auto SP aLP TimerRepeat Playback Auto TimerAuto Power Off/3H Next Function MemoryConnection to a Stereo System AUX in or Tape MonitorVideo Channel Set Access Video Channel ModeExit Video Channel Set Mode Set Video ChannelTuner Set Auto Channel SetupSET using the Aand Bbuttons and press Or E twice Perform auto channel set Move the highlight bar to Auto CHManual Channel Setup Button on the Remote Control to move the highlight barPress Or E Delete a Channel To the preset position you want then pressChange Station Name Confirmation screen appearsButton to move the station to the new preset position Change Station Preset PositionButton on the Remote Control until the item you want to Then pressFine-Tuning Stored Channels TV Station ID GuideTV Station Channel Number Guide BBC1 BBC2 ITV CH4 CH5Setting the Clock Or E. The dateOr E. Set the correct year Manually Setting Guide Program Numbers Guide Program NumbersCan the VCR indefinitely remain in the still mode? Uand cremain lit on the display panel. Is there a problem?Question and Answers Can the VCR indefinitely remain in the Record-Pause mode?Troubleshooting Symptom Possible CauseRecording Other Problems List of Terms Memo Memo Memo HR-J795EK