JVC HR-J795EK manual Advanced features

Page 40

40

advanced features

programme satellite receiver Enter the details of the programme into your satellite receiver (see receiver manual) and put a tape in the VCR.

set tape speed Press /on the Remote Control to set the tape speed to either SP or LP.

engage vcr in auto mode Press and hold SATcon the VCR for about 2 seconds. The SATc indicator on the VCR display panel lights up and the VCR turns off automatically. Any signal detected at the L-2 IN/DECODER connecter will automatically start the VCR recording; when the signal stops, so will the VCR.

Notes

connectors Auto Satellite Prog Recording is only possible using the L-2 IN/DECODER connec- tor.

timer mode You cannot put the VCR into TIMER MODE when using Auto Satellite Prog Recording Mode.

rThe number of programmes recorded will not be displayed on the VCR display panel when the rbutton is pressed.

timer recording Auto Satellite Prog Recording is not possible if your satellite receiver does not have a timer.

indicator The SATcindicator light flashes when Auto Satellite Prog Recording is in progress.

disengage To disengage the VCR during Auto Satellite Prog Recording, press the obutton. The VCR will stop recording and turns off.

tape speed When recording two or more programmes consecutively, you cannot set a different tape speed for each programme. The first speed selected will apply to all programmes in that recording session.

b.e.s.t. The B.E.S.T. system will not work during Auto Satellite Prog Recording.

just clock Just Clock does not work when in Auto Satellite Prog Recording mode.

incoming signal The VCR will only react to the start of an incoming signal at the L-2 IN/ DECODER connecter. If you try to engage Auto Satellite Prog Recording Mode whilst the satellite receiver is powered on, the SATcindicator light will flash but the VCR will not record. You must power the satellite receiver off then on again to begin recording in these circumstances.

cable input You can record in the same way from a cable system as long as you connect the cable system has a timer on/off function and is connected to the L-2 IN/DECODER connector.

incompatibilities Some satellite receivers output signals even when turned off. These receiv- ers cannot be used with this VCR in this way.

Image 40

Contents HR-J795EK Safety Precautions Blue to N Neutral or Black Brown to L Live or RedMoisture Condensation Some Do’s And Don’ts On The Safe Use Of EquipmentContents Front panel Diagram Key Front PanelWelcome to JVC Getting Everything ReadyPerform Auto Setup pg Auto Setup Three-Step Quick StartPreset Download Check the Results Finish OffGo straight to 2000 used as example only Perform Clock Set on Go to StepBasic Features Playback Load a Video CassettePlay Stop & EjectVideo Heads Cleaning Rewind and Fast ForwardPlayback Features Pg , 24H Express Timer Programming pg , etcAdvanced JOG Dial Pause During PlaybackVariable Speed Search Slow MotionHigh Speed Search Recording Choose a ProgrammeSet the Tape Speed Start RecordingDisplay Tape Remaining Time Resetting the CounterChange Display Information Instant Timer Recording Recording Resume FunctionEnter the PlusCode Number Get to the Video Plus + ScreenPress p. You will see the following TV screen information Return to Normal Screen Engage Timer Mode Get to the Programme Screen Express Timer ProgrammingEnter Programme Details AUX 24H Express Timer Programming Press c, then press oto disengage the timer mode Check, Cancel & Change ProgrammesTimes as necessary Basic features Advanced Features Manual Tracking Picture QualityPicture Control Recording and Playback Using B.E.S.T Avoiding B.E.S.T. Time DelayB.E.S.T Picture System Turning B.E.S.T. on or OFFNicam Stereo and Bilingual Broadcasts Sound ModesSoundtrack Selection Finding Specific Scenes Skip SearchIndex Search Instant ReViewTV Auto Power On You can use your TV’s Remote Control to turn off the VCRLink Functions NexTView LinkButtons. Press Or E to select on or Direct RecRecording on Satellite Receiver Control Settings Installing Satellite ControllerSetting satellite receiver’s brand SET using the Aand Bbuttons. Press Or EAppropriate number keys to enter the brand ModeCheck Result of Test Or E to finish the Sat Control Set modePress the Aand Bbuttons to move Auto Satellite Auto Record from Satellite ReceiverAdvanced features Editing Using Another VCR EditingEditing from a Camcorder Start recorder Press TOther Functions On-Screen Display O.S.DPower Save Mode Auto SP aLP TimerAuto Timer Auto Power Off/3HRepeat Playback Next Function MemoryConnection to a Stereo System AUX in or Tape MonitorAccess Video Channel Mode Exit Video Channel Set ModeVideo Channel Set Set Video ChannelAuto Channel Setup SET using the Aand Bbuttons and press Or E twiceTuner Set Perform auto channel set Move the highlight bar to Auto CHButton on the Remote Control to move the highlight bar Manual Channel SetupPress Or E To the preset position you want then press Change Station NameDelete a Channel Confirmation screen appearsChange Station Preset Position Button on the Remote Control until the item you want toButton to move the station to the new preset position Then pressFine-Tuning Stored Channels TV Station ID GuideTV Station Channel Number Guide BBC1 BBC2 ITV CH4 CH5Or E. The date Setting the ClockOr E. Set the correct year Manually Setting Guide Program Numbers Guide Program NumbersUand cremain lit on the display panel. Is there a problem? Question and AnswersCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?Troubleshooting Symptom Possible CauseRecording Other Problems List of Terms Memo Memo Memo HR-J795EK