JVC HR-S9800U manual Basic Playback, Load a cassette, Start playback

Page 23

BASIC PLAYBACK AND RECORDING

EN 23

Basic

Playback

Turn on the VCR and the TV, and select the VCR channel 3 or 4 (or AV mode) on the TV.

This VCR can check the tape condition during playback (and recording), and realizes the best possible pictures.

When you play back a tape recorded on this VCR, you can use the Video Navigation function ( pg. 46).

1 Load a cassette

Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR.

Do not apply too much pressure when inserting.

POWER	2

	STOP/EJECT	1	TIME SCAN	2
			SHUTTLE ring
	( 7 / 0 )

VCR TV CABLE/DBS

POWER

1 2 3

4 5 6

The VCR turns on automatically.

The counter is automatically reset to “0:00:00”. The tape will run for a few seconds while the VCR searches for the tape number. If the tape number is found, it will be shown on the TV screen if “SUPERIMPOSE” is set to “ON.” ( pg. 56, 57)

If the cassette’s record safety tab has been removed, playback begins automatically.

Start playback

Press PLAY ( 3 ).

Tape speed (SP or EP) is automatically detected. The S-VHS indicator lights up when you play back a tape recorded in S-VHS mode or in S- VHS ET mode ( pg. 31).

If “VIDEO CALIBRATION” is set to “ON” (default setting: pg. 57), “VIDEO CALIBRATION” appears on the screen, and this VCR checks the tape condition during automatic tracking.

7	8	9	To stop playback

0

Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7 / 0 )

on the front panel.

2

REW ( 1 )

FF ( ` )

STOP ( 7 )

To rewind the tape (when it is not running)

Press REW ( 1 ) (or turn the TIME SCAN SHUTTLE ring on the front panel to the left).

To fast-forward (when it is not running)

Press FF ( ` ) (or turn the TIME SCAN SHUTTLE ring on the front panel to the right).

To eject the tape

Press STOP/EJECT ( 7 / 0 ) on the front panel when the tape is not running.

You can also eject the cassette when the VCR is turned off.

To turn off the VCR

Press POWER.

NOTE:

When you use the Video Navigation function, operate the VCR only after the tape number is detected; otherwise, you cannot use the Video Navigation function.

Image 23

Contents HR-S9800U Telephone Number Dear CustomerGrounding or Polarization Power SourcesPower Cord Protection Power LinesReplacement Parts AccessoriesDamage Requiring Service CleaningContents Back of VCR Basic ConnectionsConnect VCR to TV Check contents Final preparation for useSituate VCR Auto Clock Set/Auto Tuner Set Plug & Play SettingPerform Plug & Play setup What to do if Plug & Play setting failedPress Menu Language SettingSelect language Return to normal screen10 EN Clock SettingAccess Main Menu screen Access Clock Set screenSelect host channel Setting clock semiautomaticallySelect D.S.T. mode Set Auto Clock to onSet year Setting clock manually12 EN Set timePerform Auto Channel Set Tuner SettingSetting channels automatically Access Tuner Set screenAdd or skip desired channels Setting channels manuallyAccess Manual Channel Set screen 14 ENPress the NumberCH 45 ADD Setting ghost reductionSelect a channel and set ghost reduction Mode What is a ghost?16 EN Cable Box Control SettingInstalling Controller Turn on cable box Setting cable box output channel & brandAccess Main Menu screen on VCR Access Cable Box Set screenEnter cable box brand Access Cable Box Brand Set screen18 EN Select cable box output channelBrand Code Cable BOX Brand ListConnect Controller to VCR How to control the DBS receiver20 EN Connect DBS receiver to VCRDBS Receiver SET, then press OK or # Setting DBS receiver output channel & brandAccess DBS Receiver Set screen Turn on DBS receiverEnter DBS Receiver’s brand AccessPress OKDBS. Receiver Brand Set screen22 EN Start playback Basic PlaybackLoad a cassette Checking tape position Basic Playback Features24 EN Changing display informationAutomatic operations after Adjusting tracking conditionPlaying back tape repeatedly Selecting monitor soundLocating beginning Locating beginning of timerAccess distant code 26 ENDigital TBC/NR Adjusting picture conditionSkipping unwanted portions Skip SearchSet tape speed Basic Recording28 EN Select recording channelPress Pause 8. To resume recording, press Play To fast-forward the tape when it is not runningTo pause recording To stop recordingSpecifying recording length Basic Recording Features30 EN Showing on-screen display Watching one program while recording another32 EN Adjusting recording levelAdjust recording level Accidental erasure prevention Record safety tabOther useful functions for recording Rapidly Picture Search High-Speed Picture Search Special Effect Playback34 EN Locating particular sceneVariable-Speed Picture Search Viewing still picturePause during playback Advance or reverse still pictureOn the Remote During normal playback 36 ENViewing slow motion picture Slow Motion Playback Pro-SlowPlayback tape How to use the Shuttle ring on the RemoteTimeScan function Sounds reproduced by the TimeScan functionStop + VCR Plus+ Timer ProgramingAccess VCR Plus+ screen 38 ENSet tape speed Press SP/EP Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Input receiving channel numberVCR Plus+ guide channel matching Changing VCR Plus+ Setting40 EN Input guide channel number Access Guide Channel Set screen42 EN Express Timer ProgramingTo timer-record daily Monday-Friday or weekly serials 44 EN Checking program settingsProgram Confirm overlapping programsSelect program to modify Select program Access Title screenNavigation Playback 46 ENDeactivate Video Navigation Deactivating Video NavigationEditing tape title Access Edit Title screenEditing Titles 48 ENEnter title How to enter the charactersEditing program title and category Select tape title3 D 2,3 Cancel50 EN Deleting tape informationDelete program information Deleting program informationChecking memory Check memoryFinding by tape number Access tape number screenFinding Tapes 52 ENConfirm tape number lists Finding by categoryFinding by recording date Conform tape number lists3,5 Access Find Title screen54 EN Finding by remaining timePosition Unrecorded portion Current tapeSelect Function Access Function Set screenChange setting 56 ENOFF When this function is set to onWhen this function is set to OFF For Example 58 ENHI-FI Video 60 ENAV Compu Link Press REC Link Set timer program on DBS receiverEngage Satellite Auto Recording standby mode Make sure the record safety tab is intact62 EN Child LockReturn to normal screen Select Jlip ID Number Set screenSet Jlip ID Number To Jlip ID NO. SETVarious connection for editing tapes Edit From Camcorder64 EN ConnectionSet Picture Control to Edit Select input mode on this VCRMake connections Select video input terminalLoad cassettes Select edit modeEdit To Or From Another 66 ENTo stop audio dubbing Activate Audio Dubbing modeLocate start point Start audio dubbingAV Dubbing Source tape Edited tape 68 ENAnother VCR for playback Insert Editing Source tape Edited tapeStart editing Activate editing modePrepare tapes Locate end point70 EN TV Brand SettingOperate cable box Cable Box Brand SettingTurn on the cable box Enter cable box brand codeEnter DBS receiver brand code DBS Receiver Brand Setting72 EN Turn on the DBS receiverTurn on VCR Changing Remote Control CodeUnplug VCR Plug in VCR74 EN TroubleshootingCorrective Action Timer RecordingMoisture Condensation About Head Cleaning76 EN Recording Questions and answersTimer Recording PlaybackList of terms 78 EN$ % Front panelRemote PAUSE/AV Compulink terminal 80 ENRear panel On-screen displayRemote How to use the RemoteUsable cassettes TimerAccessories 82 ENNew Maple Avenue Pine Brook, NJ 781 954 65084 EN Limited WarrantyMemo 86 EN Page HR-S9800U