JVC HR-S9800U manual Confirm overlapping programs, Select program to modify, Program

Page 45

EN 45

C Whenother programs overlap each

If “PROGRAM NOT COMPLETED PROGRAM OVERLAP” appears, you have another program overlapping the program you have just made.

The Program Check screen appears and conflicting programs will start blinking.

 

PR START

STOP

CH

DATE

PROGRAM NOT COMPLETED

1

8:00P

11:00

12

12/24

2

10:00A

10:45

40

12/25

PROGRAM OVERLAP

3

11:30P

1:00

125

12/25

4

9:00P

10:00

10

12/24

 

5

 

 

 

 

 

6

 

 

 

 

7

8

(5,°), THEN (3) (PROG.) : END

EX. Program 1 (you have just made) and Program 4

overlap each other

1 Confirm overlapping programs

Overlapping programs blink on the screen.

2 Select program to modify

Press %Þ, then press #.

•You can only select one of the overlapping programs.

NOTE:

If you do not mind this overlap, press PROG. to finish the timer program setting. See “ATTENTION” to the right. Without doing anything for about 1 minute, the VCR will finish the timer programing.

3 Cancel or change program setting

To cancel a program, press CANCEL when the Program screen you do

not want is shown.

PROGRAM 4

“PROGRAM

START

STOP

COMPLETED” appears on

9:00 PM

= 10:00PM

DATE

CH

the screen for about 5

12/24/00

10 SP

seconds, then normal

SUN

 

PRESS (CANCEL) TO CANCEL

screen appears.

PRESS (OK) TO CONFIRM

PRESS (PROG.) TO END

 

To change a program,

press the appropriate button: START+/–, STOP+/–, DATE+/–, CH+/–, and/or SP/EP ( ) when the Program screen on which you want to make changes is shown, then press OK.

“PROGRAM COMPLETED” appears on the screen for about 5 seconds, then normal screen appears.

NOTE:

If the overlap is not yet solved or another overlap occurs with the timer program setting made last, after making correction on a program, the conflicting programs will be shown on the Program Check screen again. Repeat the above steps again until the overlap is solved.

ATTENTION

If there is a conflict in the timer schedule and one program overlaps with another, only the parts shown below in gray will be recorded.

Pattern 1: The program with the lower program number will be recorded.

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

Program 2

 

 

 

 

 

 

Not recorded

 

 

CH40

 

 

 

Pattern 2:

The program starting earlier will be

 

recorded.

 

 

 

 

 

 

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

 

Program 2

 

 

 

Not recorded

 

CH40

 

 

Pattern 3: The program starting earlier will be recorded, followed by the remaining portion of the other program.

10:00

11:00

12:00

Program 1

 

CH10

 

 

 

 

Program 2

 

 

 

 

 

CH40

Not recorded

Page 44 Page 46
Image 45
Page 44 Page 46
Contents HR-S9800U Telephone Number Dear CustomerPower Cord Protection Power SourcesPower Lines Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Back of VCR Basic ConnectionsCheck contents Final preparation for use Situate VCRConnect VCR to TV Perform Plug & Play setup Plug & Play SettingWhat to do if Plug & Play setting failed Auto Clock Set/Auto Tuner SetSelect language Language SettingReturn to normal screen Press MenuAccess Main Menu screen Clock SettingAccess Clock Set screen 10 ENSelect D.S.T. mode Setting clock semiautomaticallySet Auto Clock to on Select host channel12 EN Setting clock manuallySet time Set yearSetting channels automatically Tuner SettingAccess Tuner Set screen Perform Auto Channel SetAccess Manual Channel Set screen Setting channels manually14 EN Add or skip desired channelsSelect a channel and set ghost reduction Mode Setting ghost reductionWhat is a ghost? Press the NumberCH 45 ADDCable Box Control Setting Installing Controller16 EN Access Main Menu screen on VCR Setting cable box output channel & brandAccess Cable Box Set screen Turn on cable box18 EN Access Cable Box Brand Set screenSelect cable box output channel Enter cable box brandBrand Code Cable BOX Brand List20 EN How to control the DBS receiverConnect DBS receiver to VCR Connect Controller to VCRAccess DBS Receiver Set screen Setting DBS receiver output channel & brandTurn on DBS receiver DBS Receiver SET, then press OK or #AccessPress OKDBS. Receiver Brand Set screen 22 ENEnter DBS Receiver’s brand Basic Playback Load a cassetteStart playback 24 EN Basic Playback FeaturesChanging display information Checking tape positionPlaying back tape repeatedly Adjusting tracking conditionSelecting monitor sound Automatic operations afterAccess distant code Locating beginning of timer26 EN Locating beginningSkipping unwanted portions Adjusting picture conditionSkip Search Digital TBC/NR28 EN Basic RecordingSelect recording channel Set tape speedTo pause recording To fast-forward the tape when it is not runningTo stop recording Press Pause 8. To resume recording, press PlayBasic Recording Features 30 ENSpecifying recording length Showing on-screen display Watching one program while recording anotherAdjusting recording level Adjust recording level32 EN Record safety tab Other useful functions for recordingAccidental erasure prevention 34 EN Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchPause during playback Viewing still pictureAdvance or reverse still picture Variable-Speed Picture SearchViewing slow motion picture 36 ENSlow Motion Playback Pro-Slow On the Remote During normal playbackTimeScan function How to use the Shuttle ring on the RemoteSounds reproduced by the TimeScan function Playback tapeAccess VCR Plus+ screen VCR Plus+ Timer Programing38 EN Stop +To use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Set tape speed Press SP/EPChanging VCR Plus+ Setting 40 ENVCR Plus+ guide channel matching Input guide channel number Access Guide Channel Set screen42 EN Express Timer ProgramingTo timer-record daily Monday-Friday or weekly serials 44 EN Checking program settingsConfirm overlapping programs Select program to modifyProgram Navigation Playback Access Title screen46 EN Select programDeactivate Video Navigation Deactivating Video NavigationEditing Titles Access Edit Title screen48 EN Editing tape titleEditing program title and category How to enter the charactersSelect tape title Enter title50 EN CancelDeleting tape information 3 D 2,3Checking memory Deleting program informationCheck memory Delete program informationFinding Tapes Access tape number screen52 EN Finding by tape numberFinding by recording date Finding by categoryConform tape number lists Confirm tape number lists54 EN Access Find Title screenFinding by remaining time 3,5Position Unrecorded portion Current tapeChange setting Access Function Set screen56 EN Select FunctionWhen this function is set to on When this function is set to OFFOFF For Example 58 ENHI-FI 60 EN AV Compu LinkVideo Engage Satellite Auto Recording standby mode Set timer program on DBS receiverMake sure the record safety tab is intact Press REC Link62 EN Child LockSet Jlip ID Number Select Jlip ID Number Set screenTo Jlip ID NO. SET Return to normal screen64 EN Edit From CamcorderConnection Various connection for editing tapesMake connections Select input mode on this VCRSelect video input terminal Set Picture Control to EditEdit To Or From Another Select edit mode66 EN Load cassettesLocate start point Activate Audio Dubbing modeStart audio dubbing To stop audio dubbingAnother VCR for playback 68 ENInsert Editing Source tape Edited tape AV Dubbing Source tape Edited tapePrepare tapes Activate editing modeLocate end point Start editing70 EN TV Brand SettingTurn on the cable box Cable Box Brand SettingEnter cable box brand code Operate cable box72 EN DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand codeUnplug VCR Changing Remote Control CodePlug in VCR Turn on VCR74 EN TroubleshootingCorrective Action Timer RecordingAbout Head Cleaning 76 ENMoisture Condensation Timer Recording Questions and answersPlayback RecordingList of terms 78 EN$ % Front panelRear panel 80 ENOn-screen display Remote PAUSE/AV Compulink terminalRemote How to use the RemoteAccessories Timer82 EN Usable cassettesNew Maple Avenue Pine Brook, NJ 781 954 65084 EN Limited WarrantyMemo 86 EN Page HR-S9800U
Top Page Image Contents