JVC HR-S7900U manual 18 EN, Connect DBS receiver to VCR, Connect Controller to VCR, Antenna Video

Page 18

18 EN

INITIAL SETTINGS (cont.)

DBS Receiver Control Setting

Suggested location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver’s remote sensor.

ATTENTION:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the Controller so its signal reaches the remote sensors on both the DBS receiver and cable box.

DBS receiver

Controller

Your VCR(suggested

locations)

DBS receiver

Controller

 

To

To

RF output

Audio/Video

Transmitter

output

or

To

To

AUDIO/

ANTENNA IN

VIDEO IN

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) receiver. The Controller allows the VCR to automatically switch the DBS receiver’s channels during timer recording.

NOTES:

●The VCR can automatically change the DBS receiver channels using the Controller when the VCR has been programed using Express timer programing (☞ pg. 34) Because satellite programing does not use PlusCode, the Controller cannot change the DBS receiver channels during VCR Plus+ timer recording.

●If a cable box is also used, it is recommended that you connect the DBS receiver to your VCR’s audio/video input connectors and the cable box to your VCR’s antenna input terminal.

Installing Controller

1 Situate Controller

Place the Controller so that its transmitter is facing the DBS receiver’s remote sensor.

●Make sure the path between the Controller and the DBS receiver’s remote sensor is not blocked.

2 Attach Controller

Fix securely using the adhesive strip attached on the back of the Controller.

3Connect DBS receiver to VCR

●If your DBS receiver does not have audio/ video output connectors

Connect the RF output terminal on the DBS receiver to the ANTENNA IN terminal on the rear of your VCR.

●If your DBS receiver has audio/video output connectors

Connect an audio/video cable between the AUDIO/VIDEO IN connectors on the rear of the VCR and the audio/video output connectors on the DBS receiver.

NOTE:

When connecting your DBS receiver, refer to its instruction manual.

4 Connect Controller to VCR

Your VCR

Connect the Controller to the CABLE BOX

Controller connector on the rear panel.

CABLE

BOX

How to control the DBS receiver

This VCR has two separate methods to control your DBS receiver.

●The VCR’s wireless Remote can control your DBS receiver. This eliminates the need for a separate DBS receiver’s Remote.

●The VCR’s Controller can also control your DBS receiver. This allows the VCR to change your DBS receiver’s channel number during timer-recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 54. To set up the Controller, go to page 19.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents HR-S7900U Dear Customer Telephone NumberPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Basic Connections Audio OUTVideo OUT Connect VCR to TV Check contentsSituate VCR Set VCR channelWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup Clock and tuner channels will be set automaticallyAccess Initial Set screen Language SettingAccess Main Menu screen Select languagePreparations Clock Setting10 EN Select clock setSet Auto Clock to on Setting clock semiautomaticallySelect D.S.T. mode Select host channel#.Set time Setting clock manually12 EN To make corrections any time during the processPerform Auto Channel Set Tuner SettingAccess Tuner Set screen Automatically Auto Channel SetAdd or skip desired channels Access Manual Channel Set screen14 EN Manual Channel Set Attach Controller Cable Box Control Setting Situate Controller Connect cable box to VCR16 EN Access Main Menu screen on VCRAccess Cable Box Set screen Select cable box output channelAccessPress OKCable. Box Brand Set screen If the cable boxs channel does not change toCable BOX Brand List Connect DBS receiver to VCR How to control the DBS receiver18 EN Connect Controller to VCRSelect DBS receiver output channel Access DBS Receiver Set screenTurn on DBS receiver DBS Receiver SETAccessPress OKDBS. Receiver Brand Set screen 20 ENEnter DBS Receiver’s brand Basic Playback Load a cassetteStart playback Changing display information Basic Playback Features22 EN Checking tape positionAutomatic operations after Adjusting tracking conditionSelecting monitor sound Locating beginning24 EN Locating beginning of timerAdjusting picture condition Recordings Instant ReviewSet tape speed Basic RecordingSelect recording channel Start recordingSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherExit on-screen display Showing on-screen displayDisplay VCR status on TV screen Other useful functions for recordingLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewing still picture Skipping unwanted portionsViewing slow motion picture 30 EN VCR Plus+ Timer ProgramingDaily Cancel Enter PlusCode numberInput receiving channel number Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Or Weekly number 9. Daily orChanging VCR Plus+ Setting 32 ENVCRPlus+guidechannelmatching Shuttleplus Input guide channel numberPlus # Guide ChannelExpress Timer Programing 34 ENCatv To timer-record daily Monday-Friday or weekly serialsPressDAILYM-F DBS24HR Quick Access 24HR quick program displayTimer warning display 36 ENChecking program settings 38 EN Confirm overlapping programsSelect program to modify Change setting Useful Function SettingsAccess Function Set screen Select FunctionWhen this function is set to on When this function is set to OFFFor Example Entire program while timer-recording in SP modeWhen stopping playback Hi-Fi tracks. The main audio is not recordedAV Compulink connectors becomes possible Mode is used for recording on S-VHS tapesBy connecting other JVC’s AV Compulink components see By selecting either HI-FI L or HI-FI ROUT AV Compu LinkVCR only AV CompulinkMake sure the record safety tab is intact Set timer program on DBS receiverEngage Satellite Auto Recording standby mode 44 ENChild Lock Various connection for editing tapes Edit From Camcorder46 EN CamcorderSelect video input terminal Select input mode on this VCRMake connections Set Picture Control to EditEdit To Or From Another 48 ENConnection Locate start point Select input modeAudio Dubbing Start audio dubbingAnother VCR for playback 50 ENAudio Svideo Insert Editing Source tape Edited tapeLocate end point Prepare tapesStart editing To stop editing any time during recordingTurn on the TV TV Brand Setting52 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting54 EN Enter DBS receiver brand codeTo control two VCRs with the same Remote Changing Remote Control CodeSet remote control code for Remote Ex. To set Remote to B codeTroubleshooting 56 ENTimer Recording 58 EN Moisture CondensationCan the VCR indefinitely remain in still mode? Timer RecordingPlayback Recording60 EN List of termsPower Front panel62 EN Front display panelRear panel On-screen displayHow to use the Remote 64 ENRemote Usable cassettes HOW to Locate Your JVC Service Center 66 ENLimited Warranty HR-S7900U
Top Page Image Contents