JVC HR-S7900U manual Timer Recording

Page 57

 

 

 

 

 

 

EN 57

 

 

 

 

 

 

 

 

TIMER RECORDING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SYMPTOM

 

POSSIBLE CAUSE

 

CORRECTIVE ACTION

 

 

1.

Timer recording will not work.

 

● The clock and/or the timer have

 

Set the clock and/or timer correctly.

 

 

 

 

 

been set incorrectly.

 

 

 

 

 

 

 

● The timer is not engaged.

 

Press TIMER and make sure that ä

 

 

 

 

 

 

 

appears on the front display panel.

 

 

 

 

 

● The VCR has not been set up properly.

 

Re-perform the set-up procedures.

 

 

 

 

 

 

 

Make sure you have compensated for

 

 

 

 

 

 

 

guide channel and VCR or cable box

 

 

 

 

 

 

 

channel number mismatches

 

 

 

 

 

 

 

(☞ pg. 32).

 

 

 

 

 

 

 

 

 

 

2.

Timer programing will not work.

 

● Timer recording is in progress.

 

Timer programing cannot be performed

 

 

 

 

 

 

 

when timer recording is in progress.

 

 

 

 

 

 

 

Wait until it finishes.

 

 

 

 

 

 

 

 

 

 

3.

ä and ] on the front display

 

● The timer is engaged but there is no

 

Load a cassette with the record safety

 

 

 

panel will not stop blinking.

 

cassette loaded.

 

tab intact, or with the hole covered

 

 

 

 

 

 

 

with adhesive tape.

 

 

 

 

 

● The loaded cassette has had its

 

Remove the cassette and cover its

 

 

 

 

 

record safety tab removed.

 

hole with adhesive tape, or replace it

 

 

 

 

 

 

 

with a cassette on which the safety

 

 

 

 

 

 

 

tab is intact.

 

 

 

 

 

 

 

 

 

 

4.

ä blinks for 10 seconds and the

 

● TIMER has been pressed when there

 

Check the programed data and set

 

 

 

timer mode is disengaged.

 

are no programs in memory, or the

 

again if necessary, then press TIMER

 

 

 

 

 

timer recording program has not

 

again.

 

 

 

 

 

been set correctly.

 

 

 

 

 

 

 

 

 

 

 

 

5.

The power shuts off and ä and

 

● The tape reaches its end during

 

The program may not have been

 

 

 

] will not stop blinking.

 

timer recording.

 

recorded in its entirety. Next time be

 

 

 

 

 

 

 

sure you have enough time on the

 

 

 

 

 

 

 

tape to record the entire broadcast.

 

 

 

 

 

 

 

 

 

6. Cable channels are not automatically

 

● The Controller is not properly

 

Connect the Controller correctly

 

 

 

switched during timer recording.

 

connected to the VCR.

 

(☞ pg. 15).

 

 

 

 

 

● The output channel selected in the

 

After confirming your cable box’s

 

 

 

 

 

Cable Box Set screen is incorrect.

 

output channel number, re-access the

 

 

 

 

 

 

 

Cable Box Set screen and select the

 

 

 

 

 

 

 

correct number (☞ pg. 16).

 

 

 

 

 

● The cable box is turned off.

 

Make sure the power is on before

 

 

 

 

 

 

 

timer recording starts.

 

 

 

 

 

 

 

 

 

 

7.

Satellite channels are not

 

● The Controller is not properly

 

Connect the Controller correctly

 

 

 

automatically switched during timer

 

connected to the VCR.

 

(☞ pg. 18).

 

 

 

recording.

 

● The output channel selected in the

 

After confirming your DBS receiver’s

 

 

 

 

 

DBS Receiver Set screen is incorrect.

 

output channel number, re-access the

 

 

 

 

 

 

 

DBS Receiver Set screen and select

 

 

 

 

 

 

 

the correct number (☞ pg. 19).

 

 

 

 

 

● The VCR is not set correctly to

 

Set the correct DBS receiver brand

 

 

 

 

 

control the DBS receiver.

 

code (☞ pg. 20).

 

 

 

 

 

● The DBS receiver is turned off.

 

Make sure the power is on before

 

 

 

 

 

 

 

timer recording starts.

 

 

 

 

 

 

 

 

 

 

8.

Timer recording begins as

 

● Even though you do not use an

 

Set “CABLE BOX SET” to “OFF” (☞

 

 

 

scheduled, but the channel is

 

external cable box or DBS receiver,

 

pg. 16) or “DBS RECEIVER SET” is set

 

 

 

always incorrect.

 

“CABLE BOX SET” is set to “ON” or

 

to “OFF” (☞ pg. 19).

 

 

 

 

 

“DBS RECEIVER SET” is set to “ON”.

 

 

 

 

 

 

 

 

 

 

 

 

9.

You moved, and now VCR Plus+

 

● The receivable stations in the new

 

Re-perform the Changing VCR Plus+

 

 

 

system does not work properly.

 

area are received on different

 

Setting procedure (☞ pg. 32).

 

 

 

 

 

channels than those in the previous

 

 

 

 

 

 

 

area.

 

 

 

 

 

 

 

 

 

 

 

10.“PROGRAM FULL” is displayed on

 

● All 8 programs of the VCR’s timer

 

Wait until a space in memory clears,

 

 

 

the screen.

 

memory are used.

 

or cancel unnecessary program

 

 

 

 

 

 

 

information (☞ pg. 37).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CONTINUED ON NEXT PAGE \

Page 56 Page 58
Image 57
Page 56 Page 58
Contents HR-S7900U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents Basic Connections Audio OUTVideo OUT Situate VCR Check contentsConnect VCR to TV Set VCR channelPerform Plug & Play setup Plug & Play SettingWhat to do if Plug & Play setting failed Clock and tuner channels will be set automaticallyAccess Main Menu screen Language SettingAccess Initial Set screen Select language10 EN Clock SettingPreparations Select clock setSelect D.S.T. mode Setting clock semiautomaticallySet Auto Clock to on Select host channel12 EN Setting clock manually#.Set time To make corrections any time during the processAccess Tuner Set screen Tuner SettingPerform Auto Channel Set Automatically Auto Channel Set14 EN Access Manual Channel Set screenAdd or skip desired channels Manual Channel SetSituate Controller Cable Box Control SettingAttach Controller Connect cable box to VCRAccess Cable Box Set screen Access Main Menu screen on VCR16 EN Select cable box output channelAccessPress OKCable. Box Brand Set screen If the cable boxs channel does not change toCable BOX Brand List 18 EN How to control the DBS receiverConnect DBS receiver to VCR Connect Controller to VCRTurn on DBS receiver Access DBS Receiver Set screenSelect DBS receiver output channel DBS Receiver SETAccessPress OKDBS. Receiver Brand Set screen 20 ENEnter DBS Receiver’s brand Basic Playback Load a cassetteStart playback 22 EN Basic Playback FeaturesChanging display information Checking tape positionSelecting monitor sound Adjusting tracking conditionAutomatic operations after Locating beginningAdjusting picture condition Locating beginning of timer24 EN Recordings Instant ReviewSelect recording channel Basic RecordingSet tape speed Start recording26 EN Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherDisplay VCR status on TV screen Showing on-screen displayExit on-screen display Other useful functions for recording28 EN Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchViewing still picture Skipping unwanted portionsViewing slow motion picture Daily Cancel VCR Plus+ Timer Programing30 EN Enter PlusCode numberTo use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Or Weekly number 9. Daily orChanging VCR Plus+ Setting 32 ENVCRPlus+guidechannelmatching Plus # Input guide channel numberShuttleplus Guide Channel34 EN Express Timer ProgramingPressDAILYM-F To timer-record daily Monday-Friday or weekly serialsCatv DBSTimer warning display Access 24HR quick program display24HR Quick 36 ENChecking program settings 38 EN Confirm overlapping programsSelect program to modify Access Function Set screen Useful Function SettingsChange setting Select FunctionWhen this function is set to OFF When this function is set to onWhen stopping playback Entire program while timer-recording in SP modeFor Example Hi-Fi tracks. The main audio is not recordedBy connecting other JVC’s AV Compulink components see Mode is used for recording on S-VHS tapesAV Compulink connectors becomes possible By selecting either HI-FI L or HI-FI RVCR only AV Compu LinkOUT AV CompulinkEngage Satellite Auto Recording standby mode Set timer program on DBS receiverMake sure the record safety tab is intact 44 ENChild Lock 46 EN Edit From CamcorderVarious connection for editing tapes CamcorderMake connections Select input mode on this VCRSelect video input terminal Set Picture Control to EditEdit To Or From Another 48 ENConnection Audio Dubbing Select input modeLocate start point Start audio dubbingAudio Svideo 50 ENAnother VCR for playback Insert Editing Source tape Edited tapeStart editing Prepare tapesLocate end point To stop editing any time during recording52 EN TV Brand SettingTurn on the TV Set TV brand codeTurn on the cable box Cable Box Brand SettingEnter cable box brand code Operate cable box54 EN DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand codeSet remote control code for Remote Changing Remote Control CodeTo control two VCRs with the same Remote Ex. To set Remote to B code56 EN TroubleshootingTimer Recording Moisture Condensation 58 ENPlayback Timer RecordingCan the VCR indefinitely remain in still mode? RecordingList of terms 60 ENFront panel PowerFront display panel 62 ENOn-screen display Rear panelHow to use the Remote 64 ENRemote Usable cassettes 66 EN HOW to Locate Your JVC Service CenterLimited Warranty HR-S7900U
Top Page Image Contents