JVC HR-S7500U manual Start Search, Access Distant Code, Activate HIGH-SPEED Search

Page 25

Index Search

Index codes are placed on the tape at the start of each recording. You can find and automatically play back from the start of any recording using the Index Search function.

1

START SEARCH

While the tape is stopped, press TIME SCAN ª or

£ (@or #).

2

ACCESS DISTANT CODE

To access a recording 2–9 index codes away, press

TIME SCAN ªor £ (@or #) repeatedly until the

correct number is displayed on screen (only if "SUPER-

 

IMPOSE" is set to "ON" (pg. 28). Playback begins

 

automatically when the desired recording is located.

 

If necessary press REW or FF when play starts to

 

search visually to find the very beginning of the

 

desired program.

NOTE:

An index code is not placed on the tape when recording is paused and then resumed.

High-Speed Search

ACTIVATE HIGH-SPEED

SEARCH

1 During playback or still, press FF for forward high- speed search, or REW for reverse high-speed search.

The search speed is 7 times normal playback speed with SP recordings, and 21 times normal with EP recordings.

TimeScan will be automatically engaged during high- speed search with an SP-recorded tape.

If the tape speed changes from SP to EP during high- speed search the TimeScan mode will change to EP search mode.

During high-speed search with an EP-recorded tape, pressing TIME SCAN for the opposite direction or turning the TIME SCAN SHUTTLE ring to the

opposite direction changes it to 7x-speed TimeScan search. (pg. 35)

To resume normal playback, press PLAY.

NOTE:

For short searches, during playback or still, press and hold FF or REW for over 2 seconds. When released, normal playback resumes.

EN25

Manual Tracking

Once playback begins, the VCR’s automatic tracking function is engaged. If tracking noise appears in the picture, you can override this and make the adjustment manually.

ENGAGE MANUAL

TRACKING MODE

1 During playback, press the CH5 and ° buttons on the

VCR's front panel simultaneously to cancel the automatic tracking mode and enable manual tracking adjust.

ADJUST MANUAL

TRACKING

2 Press CH 5(+) or ° () on the VCR's front panel or remote. Press briefly for fine adjust, or press and hold for coarse adjust. Watch the screen and continue adjusting until optimum picture and sound quality are achieved.

RE-ENGAGE AUTOMATIC

TRACKING

3 Press the CH5 and ° buttons on the VCR's front panel simultaneously.

When automatic tracking is re-engaged, Video Calibration is automatically activated.

NOTES:

To obtain a noiseless still picture it may be necessary to adjust tracking in slow playback and then engage Pause.

Manual tracking is possible during hands-free slow-motion. During hands-free slow-motion playback, simply press CH 5 (+) or ° () on the VCR's front panel or remote to adjust tracking.

Image 25
Contents HR-S7500U Do not place the VCR Dear CustomerAntenna Installation Instructions InstallationUSE Before YOU Install Your NEW VCRServicing Contents Connections Connect VCR to TV Matching Transformer not suppliedPlug & Play Plug & Play SetupEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetInformation Language EN Initial SettingsScreen Select LanguageAccess Initial SET Access Main MenuAccess Clock SET ClockSET Auto Clock to on Select D.S.T. ModeSelect Host Channel Semi-AutoSET Time Select Time ZoneSET Date SET YearTuner Access Tuner SET ScreenSET Set Receivable ChannelsAccess Manual Access Main Menu ScreenChannel Add Or Delete a ChannelSituate Controller Cable Box ControlAttach Controller Connect Cable BOX to VCRTurn on Cable BOX Access Cable BOX SETSelect Cable BOX Output ChannelInitial Settings Access Cable BOX Brand SET ScreenEnter Cable BOX Brand Brand CodeDBS Receiver Control Fasten securely using the supplied adhesive stripsConnect DBS Receiver To VCR DBS receiverSelect DBS Receiver Turn on DBS ReceiverSet DBS Receiver Output Channel & DBS Receiver Brand DBS Receiver Code from Following list, then Press OK Access DBS ReceiverJVC Dish Network Echostar Dish Network JVCLoad a Cassette Simple PlaybackFind Program Start Point Start PlaybackSimple Recording Activate FRAME-BY Frame Playback Playback FeaturesStill Picture/Frame-By- Frame Playback Slow Motion/Reverse Slow MotionEngage Manual Tracking Mode Access Distant CodeAdjust Manual Tracking Start SearchVideo Stabilizer Layback and Recording FeaturesPress OK or Time Scan CH 5 or Time ScanStop Repeat Reset Counter to ZeroActivate Instant Review Superimpose ModeSET Mode Access Function SETSelect Audio Monitor Select The SoundtrackAV Compu Link Playback Perform Movie Access Skip MenuAdvance Movie AdvanceCommercial Advance works as follows Commercial AdvanceSelect CA Playback SET Mode Time Scan Audio signal during TimeScanVariable-Speed Search/ Reverse Motion Playback Playback tape 1 2 3 4Skip Search Skip Over Unwanted SectionsSpeed Audio output Audio isSelect Timescan Audio Mode Access Function SET ScreenTimeScan Audio Place MenuDigital R3 Select Digital TBC/NRDigital TBC/NR Video Calibration Active Video CalibrationThen press OK or Time Scan #to set to on or OFFRecording PlaybackRecording Features VHS Super VHS, S-VHS ET and VHS Engage S-VHS ET Mode Select S-VHS ET SET ModeSuper VHS ET Stereo And SAP Second Audio Program Select 2ND Audio Record SET ModeTo Record SAP Programs Control Screen Adjust AudioRecording Level Return to NormalTimer Recording VCR Plus+ Timer ProgrammingAccess VCR PLUS+ Screen NumberEN Timer Recording Engage Timer ModeCheck Program Data VCR Plus+ Guide Channel Matching VCR Plus+ SetupInitial SET, then press OK or Time Scan #Ex. When inputting the Guide Channel number 6 for WNJUInd Access Guide Channel SET ScreenInput Guide Channel Number Input Receiving Channel NumberSET Program Date Express Timer ProgrammingSET Channel Number Set to OFF pg , Press SP/EP to set the tape speedBand indication TV or Catv Or DBS appears underRE-ENGAGE Timer Cancel or Revise aCheck, Cancel And Revise Programs ProgramAuto SP=EP Timer Select Auto SP=EP Timer SET ModeAuto Timer Or Time Scan %ÞEngage ITR Mode Instant Timer Recording ITRSET Recording Duration Press REC on the front panelAutomatic Sat- ellite Program Recording Prog REC ModeBefore performing the following steps Edit To Or From Another Edit From a Camcorder SET RECORDER’S Input ModeMake Connections Load a CassetteAccess Function SET Screen Enable Remote Pause FunctionStart Player Start RecorderInsert Editing Reset the CounterLocate END Point Locate Start PointStart Editing Engage Insert EditingEND Insert Editing Audio Dubbing SET RECORDER’S Input ModeEngage Audio Dubbing Start DubbingTV Multi-Brand Remote Control Speci AL Features ENTurn on the TV SET TV Brand CodeCable Box Multi-Brand Remote Control EN Special FeaturesTurn on the Cable BOX Operate Cable BOXTurn on the DBS Receiver DBS Receiver Multi-Brand Remote ControlEnter DBS Receiver Brand Operate DBS ReceiverSET Remote Control Unplug Vcrs PowerPlug in Power Cord Turn VCR Power onCassette gets stuck partway TroubleshootingRoubleshooting Timer againWhen scanning channels, some Other ProblemsCan the VCR indefinitely remain in the still mode? EN Question S and AnswersCan the VCR indefinitely remain in the Record-Pause mode? What happens if the tape runs out during recording?MBR Multi-Brand Remote Code Setting Express Timer ProgrammingIndex List Of TermsFront View Rear View Remote Control Speci Fications Video connectors in x 1, OUT x20C to 60C -4F to140F HOW to Locate Your JVC Service Center Limited Warranty HR-S7500U