JVC HR-S7500U manual EN Question S and Answers, Can the VCR indefinitely remain in the still mode?

Page 68

68ENQUESTIONSANDANSWERS

PLAYBACK

Q. What happens if the end of the tape is reached during playback or search?

A. The tape is automatically rewound to the beginning.

Q. Can the VCR indefinitely remain in the still mode?

A.No. It stops automatically after 5 minutes to protect the heads.

Q.During search, still and frame-by-frame playback, the picture is intermittent. What’s the cause?

A.Picture loss occurs when these types of playback are attempted with a tape recorded in LP mode. Pressing PLAY to return to normal playback will restore the

RECORDING

Q. When I pause and then resume a recording, the end of the recording before the pause is overlapped by the new recording. Why does this happen?

A.This is normal. It reduces distortion at the pause and resume points.

Q.Can the VCR indefinitely remain in the Record-Pause mode?

A.No. The VCR automatically goes to its Stop mode after 5 minutes to protect the heads. When paused during Instant Timer Recording (ITR), the VCR shuts off automatically after 5 minutes.

picture.

Q. When playing back programs that have been timer- recorded with consecutive times (such one program from 8:00 to 9:00 and another one from 9:00 to 10:00), the picture and sound become momentarily distorted at the point where the first program ends and the second program begins. Is this a malfunction?

A. No. This is normal.

Q. What happens if the tape runs out during recording?

A.The VCR automatically rewinds it to the beginning.

TIMER RECORDING

Q. REC and ä remain lit on the front display panel. Is there a problem?

A.No. This is a normal condition for a timer recording in progress.

Q.Can I program the timer while I’m watching a tape or a TV broadcast?

Q. Other than preventing further recording, what effect does removing the safety tab have?

A.It disables marking of index codes.

Q.Sometimes, during Index Search, the VCR can’t find the program I want to see. Why not?

A.There may be index codes too close together.

Q.During playback, on-screen operational indicators sometimes jitter. Why does this happen?

A.If the condition of the tape being played back is not good, jittering of the video (including on-screen indicators) may occur.

A.Yes, but while you are setting the timer you won't see the tape's or broadcast program's picture as it is replaced by the on-screen menu. The audio from the tape or broadcast program will be present during the setting of the timer.

Page 67 Page 69
Image 68
Page 67 Page 69
Contents HR-S7500U Dear Customer Do not place the VCRInstallation Antenna Installation InstructionsServicing Before YOU Install Your NEW VCRUSE Contents Connections Matching Transformer not supplied Connect VCR to TVPlug & Play Setup Plug & PlayEN I Nitial Sett Ings Auto Clock Set/Auto Tuner SetInformation EN Initial Settings LanguageScreen Select LanguageAccess Main Menu Access Initial SETAccess Clock SET ClockSelect D.S.T. Mode SET Auto Clock to onSelect Host Channel Semi-AutoSelect Time Zone SET TimeSET Date SET YearAccess Tuner SET Screen TunerSET Set Receivable ChannelsAccess Main Menu Screen Access ManualChannel Add Or Delete a ChannelCable Box Control Situate ControllerAttach Controller Connect Cable BOX to VCRAccess Cable BOX SET Turn on Cable BOXSelect Cable BOX Output ChannelAccess Cable BOX Brand SET Screen Initial SettingsEnter Cable BOX Brand Brand CodeFasten securely using the supplied adhesive strips DBS Receiver ControlConnect DBS Receiver To VCR DBS receiverSet DBS Receiver Output Channel & DBS Receiver Brand Turn on DBS ReceiverSelect DBS Receiver Access DBS Receiver DBS Receiver Code from Following list, then Press OKJVC Dish Network Echostar Dish Network JVCSimple Playback Load a CassetteFind Program Start Point Start PlaybackSimple Recording Playback Features Activate FRAME-BY Frame PlaybackStill Picture/Frame-By- Frame Playback Slow Motion/Reverse Slow MotionAccess Distant Code Engage Manual Tracking ModeAdjust Manual Tracking Start SearchLayback and Recording Features Video StabilizerPress OK or Time Scan CH 5 or Time ScanActivate Instant Review Reset Counter to ZeroStop Repeat Mode SuperimposeAccess Function SET SET ModeSelect Audio Monitor Select The SoundtrackAV Compu Link Playback Access Skip Menu Perform MovieAdvance Movie AdvanceCommercial Advance Commercial Advance works as followsSelect CA Playback SET Mode Audio signal during TimeScan Time ScanVariable-Speed Search/ Reverse Motion Playback Playback tape 1 2 3 4Skip Over Unwanted Sections Skip SearchSpeed Audio output Audio isAccess Function SET Screen Select Timescan Audio ModeTimeScan Audio Place MenuDigital TBC/NR Select Digital TBC/NRDigital R3 Active Video Calibration Video CalibrationThen press OK or Time Scan #to set to on or OFFPlayback RecordingRecording Features VHS Super VHS, S-VHS ET and VHS Super VHS ET Select S-VHS ET SET ModeEngage S-VHS ET Mode To Record SAP Programs Select 2ND Audio Record SET ModeStereo And SAP Second Audio Program Adjust Audio Control ScreenRecording Level Return to NormalVCR Plus+ Timer Programming Timer RecordingAccess VCR PLUS+ Screen NumberCheck Program Data Engage Timer ModeEN Timer Recording VCR Plus+ Setup VCR Plus+ Guide Channel MatchingInitial SET, then press OK or Time Scan #Access Guide Channel SET Screen Ex. When inputting the Guide Channel number 6 for WNJUIndInput Guide Channel Number Input Receiving Channel NumberSET Channel Number Express Timer ProgrammingSET Program Date Press SP/EP to set the tape speed Set to OFF pg ,Band indication TV or Catv Or DBS appears underCancel or Revise a RE-ENGAGE TimerCheck, Cancel And Revise Programs ProgramSelect Auto SP=EP Timer SET Mode Auto SP=EP TimerAuto Timer Or Time Scan %ÞInstant Timer Recording ITR Engage ITR ModeSET Recording Duration Press REC on the front panelBefore performing the following steps Prog REC ModeAutomatic Sat- ellite Program Recording Edit To Or From Another SET RECORDER’S Input Mode Edit From a CamcorderMake Connections Load a CassetteEnable Remote Pause Function Access Function SET ScreenStart Player Start RecorderReset the Counter Insert EditingLocate END Point Locate Start PointEND Insert Editing Engage Insert EditingStart Editing SET RECORDER’S Input Mode Audio DubbingEngage Audio Dubbing Start DubbingSpeci AL Features EN TV Multi-Brand Remote ControlTurn on the TV SET TV Brand CodeEN Special Features Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Operate Cable BOXDBS Receiver Multi-Brand Remote Control Turn on the DBS ReceiverEnter DBS Receiver Brand Operate DBS ReceiverUnplug Vcrs Power SET Remote ControlPlug in Power Cord Turn VCR Power onTroubleshooting Cassette gets stuck partwayTimer again RoubleshootingOther Problems When scanning channels, someEN Question S and Answers Can the VCR indefinitely remain in the still mode?Can the VCR indefinitely remain in the Record-Pause mode? What happens if the tape runs out during recording?Express Timer Programming MBR Multi-Brand Remote Code SettingIndex List Of TermsFront View Rear View Remote Control 20C to 60C -4F to140F Video connectors in x 1, OUT xSpeci Fications HOW to Locate Your JVC Service Center Limited Warranty HR-S7500U
Top Page Image Contents