JVC HR-S7500EK setup guide SET PDC Mode, Return to Normal, Screen, Engage RECORDER’S, Timer Mode

Page 17

ENTER PRESET POSITION

 

Press TV PROG +/– to

 

– P1 –

 

enter the preset position

 

 

 

 

6 corresponding to the

START

STOP

21:00

= 22:00

 

broadcasting station you

SP

VPS/PDC OFF

 

wish to record.

 

 

 

 

DATE

TV PROG

 

 

 

25.12

1

 

 

 

[+/–] =

BBC 1

 

 

 

 

 

 

 

[PROG] : EXIT

 

 

 

 

SP

 

 

SET TAPE SPEED

 

7 Press SP/LP (

) to set the tape speed.

 

8

SET PDC MODE

 

Press PDC to select "ON" or "OFF".

 

If "VPS/PDC ON" is displayed on the screen or "VPS/

PDC" is lit on the display panel, PDC is set to ON.

If "VPS/PDC OFF" is displayed on the screen or "VPS/

 

PDC" is not lit on the display panel, PDC is set to OFF.

"PDC Recording" in the right column.

VPS (Video Programme System) recording is not currently available in the U.K. and not possible with this recorder.

RETURN TO NORMAL

SCREEN

After confirming all information is correct, press PROG

or OK. "PROGRAM COMPLETED" appears on the

9 screen for about 5 seconds, then normal screen

appears.

Repeat steps 1 9 for each additional programme.

ENGAGE RECORDER’S

17

Satellite Receiver Users

To timer-record a satellite broadcast using Express Timer Programming:

1 Set "AV2 SELECT" to the appropriate mode. pg. 33 2 Perform steps 1 10. Enter "L-2" for the preset position

in step 6.

3 Set the satellite receiver to the appropriate channel before the selected programme begins.

4 Leave the satellite receiver's power on.

PDC Recording

Now available from some TV stations, PDC (Programme Delivery Control) is a service designed to assure safe, accurate timer recording. With this system, special code signals are transmitted together with the audio/video signals. These code signals control your video recorder and have precedence over the advertised times which you may have preset into the timer. This means that your recorder will start and stop recording when the preset TV programmes actually start and end — even if the broadcast time of a preset TV programme is changed from what has been advertised. PDC is currently available nationally on BBC1, BBC2, Ch.4 and Ch.5, except from a few small relay transmitters. Ch.3 operates a PDC service only in a very few areas. All channels intend to offer this service in due course. Check your TV programme listing guide for latest information. If the channel you intend to record does not offer a PDC service your recorder will not start recording if PDC has been selected. Be sure to set PDC to "OFF" if PDC is not available on your selected channel.

(step 8 in the left column).

NOTES:

Set the start time (PDC time) exactly as advertised in the TV listing. A different time than advertised will result in no recording.

PDC recording is also possible when a satellite receiver or a cable system is connected to AV2 IN on your recorder.

PDC recording is also possible via the AV1 IN/OUT connector and the front panel connectors.

10

TIMER MODE

Press ä(TIMER). The recorder turns off automatically

and äappears on the display panel.

To disengage the timer, press ä (TIMER) again.

To Timer-Record Weekly Or Daily Serials . . .

. . . anytime during steps 2 through 9, press WEEKLY (NUMBER key “9”) for weekly serials or DAILY (NUMBER key “8”) for daily serials (Monday – Friday). Either "WEEKLY" or "DAILY"

Timer Warning

If you have programmed your recorder to timer-record a programme or a series of programmes, a warning appears on the screen to tell you that the recording is due to start in 5 minutes.

WARNING– TIMER RECORDING

TO START SOON

[]

appears on the screen. Pressing the button again makes the corresponding indication disappear.

NOTE:

You can programme this recorder to timer-record as many as 8 programmes. If you try to programme the recorder to record a ninth, "PROGRAM FULL" appears on screen and "FULL" appears on the front display panel. To record the extra programme, you must first cancel any unnecessary programmes (pg. 18).

NOTES:

The warning only appears if you’re not in the Timer mode at the time.

If this recorder is being used as the player for tape dubbing, the warning screen will be recorded on the tape in the other video recorder.

The warning blinks for the entire 5 minutes leading up to the start of timer recording. To clear the display, press .

Image 17
Contents HR-S7500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide To connect to a TV with 21-pin AV input connector Scart AV1 OUT switchBack of TV Mains outletVideo in connector Back of TV Audio in connectorsAerial connector Mains outlet Mains Power CordGo to item Before performing the following procedure, make sure thatIf both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelLoad a Cassette PlaybackPoint Start PlaybackActivate HIGH-SPEED Search Pause During PlaybackRecording Reset Counter Select Preset to WatchEngage ITR Mode SET Counter DisplayAccess Video PLUS+ Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Program Screen Enter Pluscode NumberPDC Recording Timer WarningBefore performing Express Timer Programming Express Timer ProgrammingEnter Programme Start Time TimeTimer Mode SET PDC ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypeS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Adjust Tracking Playback Picture AdjustmentOverride Automatic Tracking ManuallySkip Over Unwanted Looking For Scene You WantSections Activate Index SearchReceiving Nicam Stereo And Bilingual Programmes Selecting Sound You WantSoundtrack Selection During PlaybackSpatializer Activate SpatializerAutomatic Satellite Programme Recording Switch SignalSatellite Receiver Unit Rear panel AV1 OUTAccess Main Menu Screen Control Your TV Using Additional Buttons TV Multi-brand Remote ControlRemote Con- trol Functions SET TV Brand CodeRE-SUPPLY Power SET Remote Control CodeSET Satellite Receiver Brand Code Operate Satellite ReceiverAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Make Connections SET RECORDER’S Input ModeSET Edit Mode SET Edit Mode Input ModeEdit To Or From Another Video Recorder Make ConnectionsTV Receiver AV2 Select SettingYour recorder SAT. See page 26 as wellAccess Mode SET Screen Access Main Menu ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsReturn to Normal Screen Auto SP→LP TimerAuto Timer Playback Activate RepeatRepeat Playback Next Function MemoryAudio Cable not provided Speaker Connection To Stereo SystemExit Video Channel SET Mode Access Video Channel SET ModeVideo Channel Set SET Video ChannelWith RF Connection Test SignalTuner Set Access Main MenuSET Auto Channel SetProcedures Screen preset positionsAfter Scan Completed Is displayed on the screenClose Confirmation Screen Storing Channels ManuallyEnter NEW Channel Information Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Select NEW Station Access Manual Channel SET ScreenClose Confirmation Select Station Name CharacterTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetGuide Program Number Set Video Plus+ SetupNumber Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgSymbolic Mode Indicators Audio OUT L/R Connectors enableProgramme Time Indicators show the programme Remote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x