JVC HR-S7500EK setup guide Video Channel Set, Access Video Channel SET Mode, SET Video Channel

Page 38

38SUBSIDIARYSETTINGS

Video Channel Set

Video Channel (RF Output Channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

STOP

IMPORTANT

Perform the following steps only if —

—Video Channel Set has not been done correctly by the Auto Set Up function (☞ pg. 8).

—interference appears in the TV picture after you have moved to a different area or a new station has started broadcasting in your area.

—you change the connection between your recorder and TV from RF connection to AV or S-VIDEO connection, or vice versa.

●If you have connected the video recorder to your TV via both the provided RF cable and a

21-pin SCART cable (AV connection), or via the provided RF cable, an S-Video cable and an audio cable (S-VIDEO connection), you do not need the video channel so you have to set the video channel to off. — Go to "With AV or S- VIDEO Connection" below.

●If you have connected the video recorder to your TV via the provided RF cable only (RF connection), you have to set the correct video channel — Go to "With RF Connection" on page 39.

– –:– –

With AV or S-VIDEO Connection

Before performing the following procedure, make sure that:

■the mains power cord is plugged into the mains outlet.

■the video recorder is turned off and there is no cassette inserted in the recorder.

■batteries have been installed in the remote control.

1 2 3

4 5 6

7 8 9

0

1

2

4

TV PROG

OK

ACCESS VIDEO CHANNEL SET MODE

	Press and hold down STOP on the recorder until the
1		display panel shows the following.
1

2	SET VIDEO CHANNEL
	Press TV PROG – until the display panel shows
		"–OUT– –".

●Now the video channel is set to off.

EXIT VIDEO CHANNEL SET MODE

3 Press OK.

To view picture signals from the video recorder, set your TV to its AV mode. Refer to the instructions supplied with your TV set for how to do this.

Image 38

Contents HR-S7500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Mains outletAerial connector Back of TV Audio in connectorsVideo in connector Mains outlet Mains Power CordBefore performing the following procedure, make sure that Go to itemAuto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPoint PlaybackLoad a Cassette Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Override Automatic Tracking Playback Picture AdjustmentAdjust Tracking ManuallySections Looking For Scene You WantSkip Over Unwanted Activate Index SearchSoundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackActivate Spatializer SpatializerSatellite Receiver Unit Switch SignalAutomatic Satellite Programme Recording Rear panel AV1 OUTAccess Main Menu Screen Remote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite ReceiverAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Make Connections SET RECORDER’S Input ModeSET Edit Mode Edit To Or From Another Video Recorder Input ModeSET Edit Mode Make ConnectionsYour recorder AV2 Select SettingTV Receiver SAT. See page 26 as wellENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsReturn to Normal Screen Auto SP→LP TimerAuto Timer Repeat Playback Activate RepeatPlayback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionSET Access Main MenuTuner Set Auto Channel SetAfter Scan Completed Screen preset positionsProcedures Is displayed on the screenClose Confirmation Screen Storing Channels ManuallyEnter NEW Channel Information Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name CharacterTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexSymbolic Mode Indicators Audio OUT L/R Connectors enableProgramme Time Indicators show the programme Remote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical