JVC HR-S7500EK setup guide Before performing the following procedure, make sure that, Go to item

Page 8
[MENU] : EXIT
AUTO SET
PLEASE WAIT

8

QUICKSETUPGUIDE (cont.)

STEP

3

AUTO SET UP

SET THE TUNER CHANNELS, CLOCK, GUIDE PROGRAM NUMBERS AND VIDEO CHANNEL*

The Auto Set Up function sets the tuner channels, clock, Video Plus+ assigned Guide Program numbers and the video channel*

automatically the first time the button on the recorder or on the remote is pressed to turn on the recorder after the mains power cord has been plugged into a mains outlet.

*Useful if you have connected the video recorder to your TV via RF connection (pg. 6). Video Channel (RF output channel) is the channel on which your TV receives picture and sound signals from the video recorder through the RF cable.

Before performing the following procedure, make sure that:

the TV aerial cable is connected to the recorder.

the mains power cord is plugged into the mains outlet.

batteries have been installed in the remote control.

1

–:–

1

2

3

 

 

 

2

 

4

5

6

 

7

8

9

2

 

0

4

 

 

 

1

3

Press . "Auto" appears on the display panel and

blinks; do NOT press any button on the

recorder or remote control until the display panel shows either the display as illustrated below in item 2 or "– – :– –". Auto Set Up usually takes about 4 – 12 minutes; the duration varies by area.

If "– –:– –" appears on the display panel,

refer to next page.

If you have connected the video recorder to

your TV via both the provided RF cable and a 21-pin SCART cable (AV connection) or via

the provided RF cable, an S-Video cable and 0 + + +

an audio cable (S-VIDEO connection) and if the TV is turned on and set to its AV mode, the AUTO SET screen will appear.

BeginningEnd

If you have connected the video recorder to your TV via the provided RF cable only (RF connection) — the channel that is shown on the display panel is your Video Channel.

To view picture signals from the video recorder, set your TV to the Video Channel. — Refer to the instructions supplied with your TV set for how to do this.

Go to item 3 .

If you have connected the video recorder to your TV via both the provided RF cable and a 21-pin SCART cable (AV connection), or via the provided RF cable, an S-Video cable and an audio cable (S-VIDEO connection)

you do not need the video channel so you have to set the video channel to off.

Press TV PROG – until the display panel shows "_OUT– –" to set the Video Channel to off.

To view picture signals from the video recorder, set your TV to its AV mode.

Refer to the instructions supplied with your TV set for how to do this. Go to item 3 .

Press OK to finish Auto Set Up and refer to next page to check the results.

ATTENTION

Once you have performed Auto Set Up, all the stored stations, Guide Program numbers and the video channel remain in the recorder's memory and the recorder will not perform Auto Set Up again. If there is a power cut and the recorder's memory backup expires you only need to reset the clock. (pg. 47)

If you have moved to a different area, perform each setting as required.

Video Channel setting (for RF connection users) pg. 38

Tuner setting pg. 40

Clock setting pg. 47

If a new station begins broadcasting in your area, perform tuner setting (pg. 40) and, if necessary, video channel setting (pg. 38).

NOTES:

Auto channel set function takes place first; it assigns automatically all receivable stations in your area.

Auto clock set function sets the clock automatically.

During auto channel set, the recorder recognizes each station name of the detected stations and stores them in the recorder's memory, then automatically sets the Video Plus+ assigned Guide Program number for those stations according to the broadcast area.

For RF connection users: The video recorder detects the channels which are not occupied by local stations and selects one channel automatically for your Video Channel that is located in the middle of more than 5 vacant channels.

If there is power cut or if you press or MENU while Auto Set Up is in progress, Auto Set Up will be inter- rupted; be sure to turn off the recorder power once and

press to turn the power back on in order to re-start Auto Set Up.

Image 8
Contents HR-S7500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide AV1 OUT switch To connect to a TV with 21-pin AV input connector ScartBack of TV Mains outletBack of TV Audio in connectors Video in connectorAerial connector Mains outlet Mains Power CordBefore performing the following procedure, make sure that Go to itemAuto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPlayback Load a CassettePoint Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Select Preset to Watch Reset CounterEngage ITR Mode SET Counter DisplayVideo Plus+ Timer Programming Access Video PLUS+ ScreenAccess Video PLUS+ Program Screen Enter Pluscode NumberTimer Warning PDC RecordingExpress Timer Programming Before performing Express Timer ProgrammingEnter Programme Start Time TimeSET PDC Mode Timer ModeReturn to Normal ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Playback Picture Adjustment Adjust TrackingOverride Automatic Tracking ManuallyLooking For Scene You Want Skip Over UnwantedSections Activate Index SearchSelecting Sound You Want Receiving Nicam Stereo And Bilingual ProgrammesSoundtrack Selection During PlaybackActivate Spatializer SpatializerSwitch Signal Automatic Satellite Programme RecordingSatellite Receiver Unit Rear panel AV1 OUTAccess Main Menu Screen TV Multi-brand Remote Control Control Your TV Using Additional ButtonsRemote Con- trol Functions SET TV Brand CodeSET Remote Control Code RE-SUPPLY PowerSET Satellite Receiver Brand Code Operate Satellite ReceiverAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Make Connections SET RECORDER’S Input ModeSET Edit Mode Input Mode SET Edit ModeEdit To Or From Another Video Recorder Make ConnectionsAV2 Select Setting TV ReceiverYour recorder SAT. See page 26 as wellAccess Main Menu Screen Access Mode SET ScreenENABLE/DISABLE ON-SCREEN Display Other FunctionsReturn to Normal Screen Auto SP→LP TimerAuto Timer Activate Repeat PlaybackRepeat Playback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerAccess Video Channel SET Mode Exit Video Channel SET ModeVideo Channel Set SET Video ChannelTest Signal With RF ConnectionAccess Main Menu Tuner SetSET Auto Channel SetScreen preset positions ProceduresAfter Scan Completed Is displayed on the screenClose Confirmation Screen Storing Channels ManuallyEnter NEW Channel Information Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Access Manual Channel SET Screen Select NEW StationClose Confirmation Select Station Name CharacterTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexSymbolic Mode Indicators Audio OUT L/R Connectors enableProgramme Time Indicators show the programme Remote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical