JVC HR-S7500EK setup guide Troubleshooting

Page 50

50

SUBSIDIARYINFORMATION (cont.)

Troubleshooting

Before requesting service for a problem, use this chart to see if you can correct the trouble yourself. Small problems are often easily corrected, and this can save you the trouble of sending your video recorder off for repair.

POWER

SYMPTOM

1.No power is applied to the recorder.

2.The clock is functioning properly, but the recorder cannot be powered.

3.The remote control won’t function.

TAPE TRANSPORT

SYMPTOM

1.The tape does not run during recording.

2.The tape will not rewind or fast- forward.

PLAYBACK

SYMPTOM

1.The playback picture does not appear while the tape is running.

2.Noise appears during visual search.

3.Noise appears during normal playback.

4.The playback picture is blurred or interrupted while TV broadcasts are clear.

5.Breaks are noticeable in Hi-Fi soundtrack.

RECORDING

SYMPTOM

1.Recording cannot be started.

2.TV broadcasts cannot be recorded.

3.Tape-to-tape editing is not possible.

POSSIBLE CAUSE

The mains power cord is disconnected.

“ä“ is displayed on the display panel with Auto Timer set to "OFF".

The batteries are discharged.

POSSIBLE CAUSE

“ is displayed on the display panel.

The tape is already fully rewound or fast-forwarded.

POSSIBLE CAUSE

If you’re using the RF OUT connec- tion . . .

. . . the TV receiver’s channel selector is not set to the VIDEO channel.

. . . the recorder's VIDEO channel has not been correctly set.

If you’re using the AV or S-VIDEO connection, the TV receiver is not set to the AV mode.

This is normal.

The automatic tracking mode is engaged.

The video heads may be dirty.

Automatic tracking is engaged.

POSSIBLE CAUSE

There is no cassette loaded, or the cassette loaded has had its Record Safety tab removed.

“L-1”, “L-2”, “F-1” or “S-1” has been selected as the input mode.

The source (another video recorder, camcorder) has not been properly connected.

All necessary power switches have not been turned on.

The input mode is not correct.

CORRECTIVE ACTION

Connect the mains power cord.

Press the äbutton to turn the “ä“ indicator off.

Replace the dead batteries with new ones.

CORRECTIVE ACTION

Press PLAY to turn the ““ indicator off.

Check the cassette.

CORRECTIVE ACTION

If you are using the RF OUT connec- tion . . .

. . . set the TV receiver to the VIDEO channel. (pg. 8)

. . . Perform "Video Channel Set" (pg. 38)

If you are using the AV or S-VIDEO connection, set the TV to its AV mode.

Try manual tracking (pg. 22).

Consult your JVC dealer.

Engage and adjust tracking manually. (pg. 22)

CORRECTIVE ACTION

Insert a cassette, or using adhesive tape, reseal the slot where the tab was removed.

Set to the desired preset.

Confirm that the source is properly connected.

Confirm that all units’ power switches are turned on.

Set the input mode to “L-1”,“L-2”, “F-1” or “S-1”.

Image 50
Contents HR-S7500EK Safety Precautions Connection to the mains supply in the United KingdomMoisture Condensation Do not place the recorderSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Back of TV AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Mains outletAerial connector Back of TV Audio in connectorsVideo in connector Mains outlet Mains Power CordBefore performing the following procedure, make sure that Go to itemAuto Set Up results appear on the display panel If both auto channel set and auto clock set have failedPoint PlaybackLoad a Cassette Start PlaybackPause During Playback Activate HIGH-SPEED SearchRecording Engage ITR Mode Select Preset to WatchReset Counter SET Counter DisplayAccess Video PLUS+ Program Screen Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Enter Pluscode NumberTimer Warning PDC RecordingEnter Programme Start Time Express Timer ProgrammingBefore performing Express Timer Programming TimeReturn to Normal SET PDC ModeTimer Mode ScreenCheck, Cancel And Replace Programmes Recording According To Tape Type VHS Super VHS and VHSS.T. Picture System Playback/ Recording According To Tape Charac- teristicsTurn on the Recorder Or press Record on the recorder RecordingPlayback Override Automatic Tracking Playback Picture AdjustmentAdjust Tracking ManuallySections Looking For Scene You WantSkip Over Unwanted Activate Index SearchSoundtrack Selection Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes During PlaybackActivate Spatializer SpatializerSatellite Receiver Unit Switch SignalAutomatic Satellite Programme Recording Rear panel AV1 OUTAccess Main Menu Screen Remote Con- trol Functions TV Multi-brand Remote ControlControl Your TV Using Additional Buttons SET TV Brand CodeSET Satellite Receiver Brand Code SET Remote Control CodeRE-SUPPLY Power Operate Satellite ReceiverAdvantages Of S-VHS Video Recorders Editing Mode SettingMinimizing Picture Degradation While Editing Make Connections SET RECORDER’S Input ModeSET Edit Mode Edit To Or From Another Video Recorder Input ModeSET Edit Mode Make ConnectionsYour recorder AV2 Select SettingTV Receiver SAT. See page 26 as wellENABLE/DISABLE ON-SCREEN Display Access Main Menu ScreenAccess Mode SET Screen Other FunctionsReturn to Normal Screen Auto SP→LP TimerAuto Timer Repeat Playback Activate RepeatPlayback Next Function MemoryConnection To Stereo System Audio Cable not provided SpeakerVideo Channel Set Access Video Channel SET ModeExit Video Channel SET Mode SET Video ChannelTest Signal With RF ConnectionSET Access Main MenuTuner Set Auto Channel SetAfter Scan Completed Screen preset positionsProcedures Is displayed on the screenClose Confirmation Screen Storing Channels ManuallyEnter NEW Channel Information Delete a Channel Change Station Preset PositionFine-Tuning Channels Already Stored Close Confirmation Access Manual Channel SET ScreenSelect NEW Station Select Station Name CharacterTV Station And ID List TV Station Channel Number Guide Clock Set Just ClockGuide Program Number Set Video Plus+ SetupNumber Questions And Answers Ä remain lit on the display panel. Is there Problem?Troubleshooting Timer Recording Won’t stopSpatializer Button enables/disables Spatializer. pg IndexSymbolic Mode Indicators Audio OUT L/R Connectors enableProgramme Time Indicators show the programme Remote Control How To Use Audio OUT x 1 S-Video connectors in x 1, OUT x DA4 Double Azimuth helical