JVC HR-S7500EK setup guide Access Main Menu Screen

Page 27

27

LINK

SP/LP

REC

 

ATTENTION

Be sure not to turn on the satellite receiver before the programme is executed; otherwise, the recorder will start recording when the satellite receiver's power is turned on.

If you have connected another appliance other than a satellite receiver to the AV2 IN connector, be sure not to engage the Auto Satellite Prog Rec mode; otherwise, the recorder will start recording when the connected appliance's power is turned on.

Auto Satellite Prog recording and timer-recording cannot be done at the same time.

When you press and hold the recorder's REC LINK button to engage the Auto Satellite Prog Rec mode, if the REC LINK button does not light but instead blinks quickly even though your satellite receiver's power is off, Auto Satellite Prog Recording will not work properly with that satellite receiver*.

If this is the case, perform "Express Timer Programming" (pg. 16) to timer-record a satellite programme.

*Some satellite receivers output signals even if the power is off. Auto Satellite Prog Recording is not possible with those satellite receivers.

Before performing the following steps:

Make sure the satellite receiver is connected to the recorder's AV2 IN connector. (pg. 26)

Programme the timer on the satellite receiver.

Insert a cassette with the safety tab in place.

ACCESS MAIN MENU SCREEN

1 Press MENU.

 

 

 

 

 

ACCESS MODE SET SCREEN

 

 

 

Move the highlight bar (pointer) to "MODE SET" by

2 pressing , then press OK or%.

 

 

 

SELECT AV2 SELECT MODE

 

 

 

Move the highlight bar

MODE SET

 

 

 

(pointer) to "AV2 SELECT",

 

 

 

 

 

 

3 by

pressing

, then press

AUTO TIMER

OFF

 

%

 

O. S. D.

ON

OK or

 

to set to "SAT".

B. E. S. T.

ON

 

 

 

 

 

 

AUTO SP=LP TIMER

OFF

 

 

 

 

 

 

S-VHS

AUTO

 

 

 

 

 

 

EDIT

ON

 

 

 

 

 

 

AV2 SELECT

SAT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[] =

 

 

 

 

 

 

 

 

[MENU] : EXIT

 

 

 

 

 

 

 

 

 

 

 

 

SET TAPE SPEED

 

 

 

4 Press SP/LP (

) to set the tape speed.

 

 

 

ENGAGE AUTO SATELLITE PROG

5

REC MODE

 

 

 

Press and hold REC LINK for about 2 seconds. The

 

 

button lights up and the recorder turns off automatically.

 

 

 

To disengage the Auto Satellite Prog Rec mode, press REC LINK. The light goes off.

If the recorder's power is off, it is not possible to engage the Auto Satellite Prog Rec mode.

NOTES:

Auto Satellite Prog recording is possible with the AV2 IN connector only.

When the Auto Satellite Prog Rec mode is engaged or the recorder's power is turned off after Auto Satellite Prog recording is finished, the recorder will not enter the Timer mode even though "AUTO TIMER" is set to "ON".

After Auto Satellite Prog recording, the number of recorded programmes will not be displayed on the front display panel for the Instant ReView function (pg. 23).

For timer programming of the satellite receiver, refer to the instruction manual of the satellite receiver.

Auto Satellite Prog recording is not possible if your satellite receiver does not have a timer.

The REC LINK button blinks while Auto Satellite Prog recording is in progress.

Pressing the recorder's button while Auto Satellite Prog recording is in progress turns off the recorder's power and disengages the Auto Satellite Prog Rec mode.

If there is more than one satellite programme you wish to record with Auto Satellite Prog Recording, it is not possible to set a different tape speed for each; the tape speed selected in step 4 will apply to all the programmes for Auto Satellite Prog recording.

The B.E.S.T. system (pg. 20) does not work while Auto Satellite Prog recording is in progress.

Just Clock (pg. 47) does not work when the Auto Satellite Prog Rec mode is engaged.

Depending on the type of satellite receiver, the recorder may not record a short portion at the beginning of the programme or may record slightly longer than the actual length of the programme.

If you engage the Auto Satellite Prog Rec mode when the satellite receiver's power is on, the recorder will not start Auto Satellite Prog recording even though the REC LINK button blinks. When the satellite receiver shuts off once and is turned back on again, the recorder starts recording.

You can also record a programme from your cable system in the same way if the system has a timer and is connected to the recorder's AV2 IN connector.

Image 27
Contents HR-S7500EK Connection to the mains supply in the United Kingdom Safety PrecautionsDo not place the recorder Moisture CondensationSome Dos And Donts On The Safe Use Of Equipment Quick SET UP Guide Mains outlet AV1 OUT switchTo connect to a TV with 21-pin AV input connector Scart Back of TVMains outlet Mains Power Cord Back of TV Audio in connectorsVideo in connector Aerial connectorGo to item Before performing the following procedure, make sure thatIf both auto channel set and auto clock set have failed Auto Set Up results appear on the display panelStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search Pause During PlaybackRecording SET Counter Display Select Preset to WatchReset Counter Engage ITR ModeEnter Pluscode Number Video Plus+ Timer ProgrammingAccess Video PLUS+ Screen Access Video PLUS+ Program ScreenPDC Recording Timer WarningTime Express Timer ProgrammingBefore performing Express Timer Programming Enter Programme Start TimeScreen SET PDC ModeTimer Mode Return to NormalCheck, Cancel And Replace Programmes VHS Super VHS and VHS Recording According To Tape TypePlayback/ Recording According To Tape Charac- teristics Turn on the RecorderS.T. Picture System Recording PlaybackOr press Record on the recorder Manually Playback Picture AdjustmentAdjust Tracking Override Automatic TrackingActivate Index Search Looking For Scene You WantSkip Over Unwanted SectionsDuring Playback Selecting Sound You WantReceiving Nicam Stereo And Bilingual Programmes Soundtrack SelectionSpatializer Activate SpatializerRear panel AV1 OUT Switch SignalAutomatic Satellite Programme Recording Satellite Receiver UnitAccess Main Menu Screen SET TV Brand Code TV Multi-brand Remote ControlControl Your TV Using Additional Buttons Remote Con- trol FunctionsOperate Satellite Receiver SET Remote Control CodeRE-SUPPLY Power SET Satellite Receiver Brand CodeEditing Mode Setting Minimizing Picture Degradation While EditingAdvantages Of S-VHS Video Recorders SET RECORDER’S Input Mode SET Edit ModeMake Connections Make Connections Input ModeSET Edit Mode Edit To Or From Another Video RecorderSAT. See page 26 as well AV2 Select SettingTV Receiver Your recorderOther Functions Access Main Menu ScreenAccess Mode SET Screen ENABLE/DISABLE ON-SCREEN DisplayAuto SP→LP Timer Auto TimerReturn to Normal Screen Next Function Memory Activate RepeatPlayback Repeat PlaybackAudio Cable not provided Speaker Connection To Stereo SystemSET Video Channel Access Video Channel SET ModeExit Video Channel SET Mode Video Channel SetWith RF Connection Test SignalAuto Channel Set Access Main MenuTuner Set SETIs displayed on the screen Screen preset positionsProcedures After Scan CompletedStoring Channels Manually Enter NEW Channel InformationClose Confirmation Screen Change Station Preset Position Fine-Tuning Channels Already StoredDelete a Channel Select Station Name Character Access Manual Channel SET ScreenSelect NEW Station Close ConfirmationTV Station And ID List TV Station Channel Number Guide Just Clock Clock SetVideo Plus+ Setup NumberGuide Program Number Set Ä remain lit on the display panel. Is there Problem? Questions And AnswersTroubleshooting Won’t stop Timer RecordingIndex Spatializer Button enables/disables Spatializer. pgAudio OUT L/R Connectors enable Programme Time Indicators show the programmeSymbolic Mode Indicators Remote Control How To Use DA4 Double Azimuth helical Audio OUT x 1 S-Video connectors in x 1, OUT x