JVC HR-V617EK, HR-V616EK, HR-V615EK manual Recording

Page 57

subsidiary information

SYMPTOM

POSSIBLE CAUSE

CORRECTIVE ACTION

57

RECORDING

1.Recording cannot be started.

2.TV broadcasts cannot be recorded.

3.Tape-to-tape editing is not possible.

4.Camcorder recording is not possible.

•There is no cassette loaded, or the cassette loaded has had its record safety tab removed.

•L-1 or L-2 has been selected as the input mode.

•The source (another VCR, camcorder) has not been properly connected.

•All necessary power switches have not been turned on.

•The input mode is not correct.

•The camcorder has not been properly connected.

•The input mode is not correct.

Insert a cassette, or using adhesive tape, cover the hole where the tab was removed.

Set to the desired preset.

Confirm that the source is prop- erly connected.

Confirm that all units’ power switches are turned on.

Set the input mode to L-1 or L-2.

Confirm that the camcorder is properly connected.

Set the input mode to L-1 or L-2.

TIMER RECORDING

1.Timer recording won’t work.

2.Timer programming is not possible.

•The clock and/or the timer have been set incorrectly.

•The timer is not engaged.

•Timer recording is in progress.

Re-perform the clock and/or timer settings.

Press cand confirm that cis displayed on the display panel.

Timer programming can’t be performed while a timer recording is in progress. Wait until it finishes.

3.con the display panel won’t stop blinking.

4.c, Uand ,on the display panel won’t stop blinking.

•The timer is engaged but there’s no cassette loaded.

•The loaded cassette has had its record safety tab removed.

•The end of the tape was reached during timer recording.

Load a cassette with the record safety tab intact.

Remove the cassette and cover the hole with adhesive tape, or insert a cassette with the record safety tab intact.

The programme may not have been recorded in its entirety. Next time make sure you have enough time on the tape to record the entire programme.

5.cblinks for 10 seconds and the Timer mode is disengaged.

•chas been pressed when there are no programs in memory, or the timer record information has been pro- grammed incorrectly.

Check the programmed data and re-programme as necessary, then press cagain.

6.The VIDEO Plus+ system does not timer record properly.

•The VCR’s preset positions have been set incorrectly.

Refer to Set Guide Program Numbers (☞ pg. 22) and re- perform the procedure.

HR-V615/616/617EK-EN/p54-59

57

3/8/04, 10:22 AM

Black

Page 56 Page 58
Image 57
Page 56 Page 58
Contents HR-V615EK HR-V616EK HR-V617EK If in doubt consult a competent electrician Safety PrecautionsMoisture Condensation On The Safe Use Of Equipment Some Do’s And Don’tsContents Rear panel Front Panel Diagram KeyGetting Everything Ready Welcome to JVCPerform Auto Setup pg Three-Step Quick Start Auto SetupThree step quick start Preset DownloadFinish Off Check the ResultsBasic Features Load a Video Cassette PlaybackPlay Stop & EjectRewind and Fast Forward Video Heads CleaningPlayback Features Pause During PlaybackSingle Frame Movement Slow Motion Variable Speed SearchPicture Search Choose a Programme RecordingSet the Tape Speed Start RecordingDisplay Tape Remaining Time Resetting the CounterChange Display Information Record a Programme While Watching AnotherRecording Resume Function Instant Timer RecordingEnter the PlusCode Number Get to the Video Plus + ScreenScreen appears Return to Normal ScreenEngage Timer Mode Get to the Timer Programming Set Screen Express Timer ProgrammingGet to the Programme Screen Enter Programme DetailsReturn to Normal Screen Press c, then press oto disengage the timer mode Check, Cancel & Change ProgrammesConfirm overlapping programmes When Programmes Overlap Each OtherBasic features Advanced Features Picture Quality Manual TrackingPicture Control Avoiding B.E.S.T. Time Delay Recording and Playback Using B.E.S.TB.E.S.T Picture System Turning B.E.S.T. on or OFFSound Modes Nicam Stereo and Bilingual BroadcastsSoundtrack Selection Skip Search Finding Specific ScenesIndex Search Instant ReviewLink Functions TV Auto Power OnNext View Link VCR Auto StandbyButton Direct RecInstalling Satellite Controller Satellite Receiver Control SettingsSET using the PR and PR buttons. Press OK button or Setting satellite receiver’s brandCheck Result of Test Auto Record from Satellite Receiver Auto SatelliteAdvanced features Editing Editing Using Another VCRStart recorder Press T Editing from a CamcorderOn-Screen Display O.S.D Other FunctionsAuto SP aLP Timer Power Save ModeAuto Power Off/3H Auto TimerRepeat Playback Next Function MemoryAUX in or Tape Monitor Connection to a Stereo SystemExit Video Channel Set Mode Access Video Channel ModeVideo Channel Set Set Video ChannelTuner Set Auto Channel SetupPress Button and you Manual Channel SetupDelete a Channel Change Station NameChange Station Preset Position TV Station ID Guide Fine-Tuning Stored ChannelsBBC1 BBC2 ITV CH4 CH5 TV Station Channel Number GuideClock Set Setting the ClockPlayback Question and AnswersSymptom Possible Cause TroubleshootingRecording Other Problems List of Terms HR-V615/616/617EK
Top Page Image Contents