JVC HR-VP78U manual Remote Control Code, Unplug VCR, Plug in VCR, Turn on VCR

Page 49

Changing 4

Remote Control

Code

EN 49

This Remote is capable of transmitting two control codes; one set to respond to A code control signals and another set to respond to B code control signals.

This Remote control is preset to send A code signals because your VCR is initially set to respond to A code signals. You can easily modify your VCR and the Remote to respond to B code signals.

When using two JVC VCRs, set two VCRs and their Remotes to different codes, so that you can operate these VCRs1separately.

Unplug VCR

2Unplug the AC power cord from the AC outlet.

1Set remote control code for Remote

1 2 3

4 5 6

7 8 9

0

2

4

2–1, 3

2–2

2Press and hold A/B.

3Press the Number key “2”. Press OK, and release A/B.

●The Remote now can transmit B code control

3signals.

Plug in VCR

4Plug the AC power cord back into an AC outlet.

Turn on VCR

1

3	–3

Press POWER on the Remote.

●The VCR now responds to B code control signals.

●To set the Remote and the VCR back to A code control signals, repeat the same procedure as shown above except pressing the Number key “1” in step 2.

To control two VCRs with the same Remote

You can control two JVC VCRs by switching the remote control2 code for the Remote between A and B ( step

), keeping two VCRs to different control codes.

●Press the Number key “1” for A code control signals and the Number key “2” for B code control signals. (To change only the remote control code for the Remote, DO NOT perform steps 1, 3, and 4.)

(Ex.) To set Remote to B code:

MBR SET
A/B		E
		E
		NTER/O
	2		SD	Release
	2	3	OK	Release
Hold	Press in succession
down

Image 49

Contents HR-VP78U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents ANT. Basic ConnectionsVideo OUT Back of VCRConnect VCR to power source Check contentsSituate VCR Connect VCR to TVPerform Plug & Play setup Plug & Play SettingWhat to do if Plug & Play setting failed During Initial Auto Clock Set During Auto Channel SetLanguage SettingPressAccessMENUMain Menu screen Access Initial Set screen Clock SettingPreparations1 Select clock setSelect D.S.T. mode Setting clock semiautomaticallySet Auto Clock to on Select host channel12 EN Setting clock manuallyAutomatically Auto Channel Set Setting channels Tuner SettingAccess Tuner Set screen Perform Auto Channel Set14 EN Setting channels manuallyManual Channel Set Situate Controller Cable Box Control SettingAttach Controller Connect cable box to VCRSelect cable box output channel Access Cable Box Set screenTurn on cable box Enter cable box brand Access Cable Box Brand Set screen18 EN How to control the DBS receiverConnect DBS receiver to VCR ControllerChannel 3 or 4 or AV mode on the TV 3Press Menu Setting DBS receiver output channel & brandTurn on DBS receiver Select DBS receiver output channel20 EN Access DBS Receiver Brand Set screenEnter DBS Receiver’s brand Playback BasicLoad a cassette Start playback22 EN Basic Playback FeaturesChanging display information Checking tape positionSelecting monitor sound Adjusting tracking conditionAutomatic operations after Access distant code Locating beginning of timer24 EN Locating beginningSelect recording channel Basic RecordingSet tape speed Start recording26 EN Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherDisplay VCR status on TV screen Showing on-screen displayErase on-screen display Accidental erasure prevention28 EN Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchSkipping unwanted portions Viewing still pictureViewing slow motion picture Pause during playbackAccess VCR Plus+ screen VCR Plus+ Timer Programing30 EN Enter PlusCode numberTo use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Check program dateVCR Plus+ Setup32 EN VCR Plus+ guide channel matchingInput guide channel number Access Guide Channel Set screenTo Initial SET, then Press OK 34 EN Express Timer ProgramingCatv To timer-record daily Monday-Friday or weekly serialsDBS 36 EN Checking program settingsSelect program to modify Confirm overlapping programsOverlapping programs blink on the screen Useful Function Settings38 EN When this function is set to OFF When this function is set to onFor Example 40 ENTelevision This VCRLink Video VCR only Video OUT Pause42 EN PreventingConnection Edit To Or From Another44 EN Edit From CamcorderThis VCR for recording Camcorder for playbackAccess Main Menu screen on this VCR Select input mode on this VCREnable remote pause function Select Edit for Picture Control46 EN TV Brand SettingTurn on the TV Set TV brand codeTurn on the cable box Cable Box Brand SettingEnter cable box brand code Operate cable box48 EN DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand codeUnplug VCR Remote Control CodePlug in VCR Turn on VCR50 EN TroubleshootingTimer Recording 52 EN Other ProblemsWhat happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?List of terms 54 ENVCR PLUS+ Still Play Slow Front panel1Record Record PauseRear panel1 56 EN78Tape speed indication 5496783 How to use the RemoteUsable cassettes 58 ENFull-Size VHS 30 ST-30 Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40HOW to Locate Your JVC Service Center 60 EN Limited WarrantyMemo 62 EN Page HR-VP78U