JVC HR-VP78U 18 EN, Connect DBS receiver to VCR, How to control the DBS receiver, Controller

Page 18

18 EN

INITIAL SETTINGS (cont.)

DBS Receiver Control Setting

Suggested location

Place the DBS (Direct Broadcast Satellite) receiver on top of the VCR. Attach the VCR’s Controller to the top of the VCR with the Controller’s transmitter pointed towards the DBS receiver’s remote sensor.

ATTENTION:

The Controller can also control a cable box. If both a DBS receiver and a cable box are used, position the Controller so its signal reaches the remote sensors on both the DBS receiver and cable box.

DBS receiver

Controller

Your VCR(suggested

locations)

DBS receiver

Controller

 

(not supplied)

 

To

To

RF output

Audio/Video

Transmitter

output

or

To

To

AUDIO/

ANT. IN

VIDEO IN

 

Your VCR

CABLE

BOX

The following procedure is required if you receive satellite channels through a DBS (Direct Broadcast Satellite) receiver. The Controller allows the VCR to automatically switch the DBS receiver’s channels during timer recording.

NOTES:

●The Controller is not supplied with this unit. It can be requested by mailing in the completed JVC Cable Mouse Certificate that is included with the accessory package.

●The VCR can automatically change the DBS receiver channels using the Controller when the VCR has been programed using Express timer programing ( pg. 34). Because satellite programing does not use PlusCode, the Controller cannot change the DBS receiver channels during VCR Plus+ timer recording.

●If a cable box is also used, it is recommended that you connect the DBS receiver to your VCR’s audio/video input connectors and the cable box to your VCR’s antenna input terminal.

1Installing Controller

Situate Controller

Place the Controller so that its transmitter is facing the DBS receiver’s remote sensor.

●Make sure the path between the Controller and the DBS receiver’s remote sensor is not

2blocked.

Attach Controller

Fix securely using the adhesive strip attached on

3the back of the Controller.

Connect DBS receiver to VCR

●If your DBS receiver does not have audio/ video output connectors

Connect the RF output terminal on the DBS receiver to the ANT. IN terminal on the rear of your VCR.

●If your DBS receiver has audio/video output connectors

Connect an audio/video cable between the AUDIO/VIDEO IN connectors on the rear of the VCR and the audio/video output connectors on the DBS receiver.

NOTE:

When connecting your DBS receiver, refer to its

4instruction manual.

Connect Controller to VCR

Connect the Controller to the CABLE BOX

Controller connector on the rear panel.

How to control the DBS receiver

This VCR has two separate methods to control your DBS receiver.

●The VCR’s wireless Remote can control your DBS receiver. This eliminates the need for a separate DBS receiver’s Remote.

●The VCR’s Controller can also control your DBS receiver. This allows the VCR to change your DBS receiver’s channel number during timer-recording.

Each method must be set up separately. To set up the VCR’s Remote, refer to page 48. To set up the Controller, go to page 19.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents HR-VP78U Dear Customer Telephone NumberPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Video OUT Basic ConnectionsANT. Back of VCRSituate VCR Check contentsConnect VCR to power source Connect VCR to TVWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup During Initial Auto Clock Set During Auto Channel SetSetting LanguagePreparations1 Clock SettingPressAccessMENUMain Menu screen Access Initial Set screen Select clock setSet Auto Clock to on Setting clock semiautomaticallySelect D.S.T. mode Select host channelSetting clock manually 12 ENAccess Tuner Set screen Tuner SettingAutomatically Auto Channel Set Setting channels Perform Auto Channel SetSetting channels manually 14 ENManual Channel Set Attach Controller Cable Box Control SettingSituate Controller Connect cable box to VCRAccess Cable Box Set screen Select cable box output channelTurn on cable box Access Cable Box Brand Set screen Enter cable box brandConnect DBS receiver to VCR How to control the DBS receiver18 EN ControllerTurn on DBS receiver Setting DBS receiver output channel & brandChannel 3 or 4 or AV mode on the TV 3Press Menu Select DBS receiver output channelAccess DBS Receiver Brand Set screen 20 ENEnter DBS Receiver’s brand Load a cassette BasicPlayback Start playbackChanging display information Basic Playback Features22 EN Checking tape positionAdjusting tracking condition Selecting monitor soundAutomatic operations after 24 EN Locating beginning of timerAccess distant code Locating beginningSet tape speed Basic RecordingSelect recording channel Start recordingSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherErase on-screen display Showing on-screen displayDisplay VCR status on TV screen Accidental erasure preventionLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewing slow motion picture Viewing still pictureSkipping unwanted portions Pause during playback30 EN VCR Plus+ Timer ProgramingAccess VCR Plus+ screen Enter PlusCode numberInput receiving channel number Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Check program date32 EN SetupVCR Plus+ VCR Plus+ guide channel matchingAccess Guide Channel Set screen Input guide channel numberTo Initial SET, then Press OK Express Timer Programing 34 ENTo timer-record daily Monday-Friday or weekly serials CatvDBS Checking program settings 36 ENConfirm overlapping programs Select program to modifyOverlapping programs blink on the screen Settings Useful Function38 EN When this function is set to on When this function is set to OFF40 EN For ExampleLink Video This VCRTelevision VCR only Video OUT PausePreventing 42 ENEdit To Or From Another ConnectionThis VCR for recording Edit From Camcorder44 EN Camcorder for playbackEnable remote pause function Select input mode on this VCRAccess Main Menu screen on this VCR Select Edit for Picture ControlTurn on the TV TV Brand Setting46 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting48 EN Enter DBS receiver brand codePlug in VCR Remote Control CodeUnplug VCR Turn on VCRTroubleshooting 50 ENTimer Recording Other Problems 52 ENCan the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?54 EN List of termsVCR PLUS+ Record Front panel1Still Play Slow Record Pause56 EN Rear panel178Tape speed indication How to use the Remote 5496783Full-Size VHS 30 ST-30 58 ENUsable cassettes Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40HOW to Locate Your JVC Service Center Limited Warranty 60 ENMemo 62 EN Page HR-VP78U
Top Page Image Contents