JVC HR-VP78U manual Can the VCR indefinitely remain in still mode?

Page 53

EN 53

Questions and answers

PLAYBACK

Q. What happens if the tape reaches its end during playback or search?

A. The VCR automatically rewinds it to the beginning.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q.Can the VCR indefinitely remain in still mode?

A.No. It stops automatically after 5 minutes to protect

the heads.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q.During picture search, still picture playback and frame-by-frame playback, the picture is intermittent. What’s the cause?

A.Picture loss occurs when these types of playback are attempted with a tape recorded in LP mode. Pressing PLAY ( 3 ) to return to normal playback will restore

the picture.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q. When returning from variable-speed picture search to normal playback, the picture is disturbed. Should I be concerned about this?

A. No, it is normal.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q. When playing back programs that have been timer- recorded consecutively (such one program from 8:00 to 9:00 and another one from 9:00 to 10:00), the picture and sound become momentarily distorted where the first program ends and the second program begins. Is this a malfunction?

A. No. This is normal.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q. Other than preventing further recording, what effect does removing the safety tab have?

A. It disables marking of index codes.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q. Sometimes, during index search, the VCR cannot find the program I want to see. Why not?

A. There may be index codes too close together.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q.During playback, on-screen display sometimes jitters. Why does this happen?

A.If the condition of the tape being played back is not good, jittering of the video (including on-screen display) may occur.

RECORDING

Q.When I pause and then resume a recording, the end of the recording before the pause is overlapped by the new recording. Why does this happen?

A.This is normal. It reduces distortion at the pause and

resume points.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q.Can the VCR indefinitely remain in the recording pause mode?

A.No. The VCR automatically stops after 5 minutes to protect the heads. When paused during Instant Timer Recording (ITR), the VCR shuts off automatically after

5 minutes.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q.What happens if the tape reaches its end during recording?

A.The VCR automatically rewinds it to the beginning.

TIMER RECORDING

Q.REC and remain lit on the front display panel. Is there a problem?

A.No. This is a normal condition for a timer recording

in progress.

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Q.Can I program the timer while I’m watching a tape or a TV broadcast?

A.Yes, but while you are setting the timer you will not see the tape’s or broadcast program’s picture as it is replaced by the on-screen menu. (The sound from the tape or broadcast program will be heard during the timer setting.)

Image 53
Contents HR-VP78U Telephone Number Dear CustomerPower Lines Power SourcesPower Cord Protection Grounding or PolarizationDamage Requiring Service AccessoriesCleaning Replacement PartsContents ANT. Basic ConnectionsVideo OUT Back of VCRConnect VCR to power source Check contentsSituate VCR Connect VCR to TVPerform Plug & Play setup Plug & Play SettingWhat to do if Plug & Play setting failed During Initial Auto Clock Set During Auto Channel SetLanguage SettingPressAccessMENUMain Menu screen Access Initial Set screen Clock SettingPreparations1 Select clock setSelect D.S.T. mode Setting clock semiautomaticallySet Auto Clock to on Select host channel12 EN Setting clock manuallyAutomatically Auto Channel Set Setting channels Tuner SettingAccess Tuner Set screen Perform Auto Channel SetManual Channel Set Setting channels manually14 EN Situate Controller Cable Box Control SettingAttach Controller Connect cable box to VCRTurn on cable box Access Cable Box Set screenSelect cable box output channel Enter cable box brand Access Cable Box Brand Set screen18 EN How to control the DBS receiverConnect DBS receiver to VCR ControllerChannel 3 or 4 or AV mode on the TV 3Press Menu Setting DBS receiver output channel & brandTurn on DBS receiver Select DBS receiver output channelEnter DBS Receiver’s brand Access DBS Receiver Brand Set screen20 EN Playback BasicLoad a cassette Start playback22 EN Basic Playback FeaturesChanging display information Checking tape positionAutomatic operations after Adjusting tracking conditionSelecting monitor sound Access distant code Locating beginning of timer24 EN Locating beginningSelect recording channel Basic RecordingSet tape speed Start recording26 EN Basic Recording FeaturesSpecifying recording length Watching one program while recording anotherDisplay VCR status on TV screen Showing on-screen displayErase on-screen display Accidental erasure prevention28 EN Special Effect PlaybackLocating particular scene Rapidly Picture Search High-Speed Picture SearchSkipping unwanted portions Viewing still pictureViewing slow motion picture Pause during playbackAccess VCR Plus+ screen VCR Plus+ Timer Programing30 EN Enter PlusCode numberTo use the VCR while it is in timer recording standby mode Engage timer recording standby modeInput receiving channel number Check program dateVCR Plus+ Setup32 EN VCR Plus+ guide channel matchingTo Initial SET, then Press OK Access Guide Channel Set screenInput guide channel number 34 EN Express Timer ProgramingDBS To timer-record daily Monday-Friday or weekly serialsCatv 36 EN Checking program settingsOverlapping programs blink on the screen Confirm overlapping programsSelect program to modify 38 EN SettingsUseful Function When this function is set to OFF When this function is set to onFor Example 40 ENTelevision This VCRLink Video VCR only Video OUT Pause42 EN PreventingConnection Edit To Or From Another44 EN Edit From CamcorderThis VCR for recording Camcorder for playbackAccess Main Menu screen on this VCR Select input mode on this VCREnable remote pause function Select Edit for Picture Control46 EN TV Brand SettingTurn on the TV Set TV brand codeTurn on the cable box Cable Box Brand SettingEnter cable box brand code Operate cable box48 EN DBS Receiver Brand SettingTurn on the DBS receiver Enter DBS receiver brand codeUnplug VCR Remote Control CodePlug in VCR Turn on VCR50 EN TroubleshootingTimer Recording 52 EN Other ProblemsWhat happens if the tape reaches its end during recording? Can the VCR indefinitely remain in still mode?VCR PLUS+ 54 ENList of terms Still Play Slow Front panel1Record Record Pause78Tape speed indication 56 ENRear panel1 5496783 How to use the RemoteUsable cassettes 58 ENFull-Size VHS 30 ST-30 Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40HOW to Locate Your JVC Service Center 60 EN Limited WarrantyMemo 62 EN Page HR-VP78U