JVC HR-VP78U manual TV Brand Setting, 46 EN, Turn on the TV, Set TV brand code, Operate TV

Page 46

46 EN

MULTI-BRAND REMOTE CONTROL

TV Brand Setting

This Remote can control some functions of remote controllable TVs listed below. Without setting, you can control1a JVC TV.

Turn on the TV

Turn on the TV using the Power button on the TV

2or its Remote.

2–14

TV TV/VCR

2–2

POWER

23

2

Set TV brand code

1Follow the example shown below.

2Press and hold TV.

3Press MBR SET.

Press the Number keys to enter your TV’s

4brand code by referring to the table below.

Press OK, and release TV.

The TV should turn off. If it does, try other

45 6 2–3

7	8	9	Number

04

operations below. ( step 3).

●Once you have set the Remote to operate the TV, you do not have to set it until you replace the batteries from the Remote.

●PANASONIC has two codes. If the TV does not

3function with one code, try entering the other.

1

2–4

3	ENTER
	TV VOL +/–
	TV CH +/–

Operate TV

While holding down TV, press one of the following buttons: POWER, TV/VCR, TV CH +/–, (TV Muting), TV VOL +/–, and Number keys.

●For some brands, you must press ENTER after having pressed the Number keys to enter a channel number.

NOTES:

●Depending on the type of TV, some or all functions cannot be operated using this Remote.

●It’s not possible to operate a TV not equipped with a remote sensor.

TV BRAND NAME	BRAND CODE
JVC	01, 03
HITACHI	10
MAGNAVOX	02
MITSUBISHI	03
PANASONIC	04, 11
RCA	05
SHARP	06
SONY	07
SAMSUNG	12
SANYO	13
SEARS	13
TOSHIBA	08
ZENITH	09

(Ex.) To set Remote to RCA 05:

	MBR SET
TV	A/B		ENTER/O
	0	5			SD
	0	5	3	O	K
				O

Hold	Press in succession
down

Release

Image 46

Contents HR-VP78U Dear Customer Telephone NumberPower Cord Protection Power SourcesPower Lines Grounding or PolarizationCleaning AccessoriesDamage Requiring Service Replacement PartsContents Video OUT Basic ConnectionsANT. Back of VCRSituate VCR Check contentsConnect VCR to power source Connect VCR to TVWhat to do if Plug & Play setting failed Plug & Play SettingPerform Plug & Play setup During Initial Auto Clock Set During Auto Channel SetSetting LanguagePreparations1 Clock SettingPressAccessMENUMain Menu screen Access Initial Set screen Select clock setSet Auto Clock to on Setting clock semiautomaticallySelect D.S.T. mode Select host channelSetting clock manually 12 ENAccess Tuner Set screen Tuner SettingAutomatically Auto Channel Set Setting channels Perform Auto Channel Set14 EN Setting channels manuallyManual Channel Set Attach Controller Cable Box Control SettingSituate Controller Connect cable box to VCRSelect cable box output channel Access Cable Box Set screenTurn on cable box Access Cable Box Brand Set screen Enter cable box brandConnect DBS receiver to VCR How to control the DBS receiver18 EN ControllerTurn on DBS receiver Setting DBS receiver output channel & brandChannel 3 or 4 or AV mode on the TV 3Press Menu Select DBS receiver output channel20 EN Access DBS Receiver Brand Set screenEnter DBS Receiver’s brand Load a cassette BasicPlayback Start playbackChanging display information Basic Playback Features22 EN Checking tape positionSelecting monitor sound Adjusting tracking conditionAutomatic operations after 24 EN Locating beginning of timerAccess distant code Locating beginningSet tape speed Basic RecordingSelect recording channel Start recordingSpecifying recording length Basic Recording Features26 EN Watching one program while recording anotherErase on-screen display Showing on-screen displayDisplay VCR status on TV screen Accidental erasure preventionLocating particular scene Special Effect Playback28 EN Rapidly Picture Search High-Speed Picture SearchViewing slow motion picture Viewing still pictureSkipping unwanted portions Pause during playback30 EN VCR Plus+ Timer ProgramingAccess VCR Plus+ screen Enter PlusCode numberInput receiving channel number Engage timer recording standby modeTo use the VCR while it is in timer recording standby mode Check program date32 EN SetupVCR Plus+ VCR Plus+ guide channel matchingInput guide channel number Access Guide Channel Set screenTo Initial SET, then Press OK Express Timer Programing 34 ENCatv To timer-record daily Monday-Friday or weekly serialsDBS Checking program settings 36 ENSelect program to modify Confirm overlapping programsOverlapping programs blink on the screen Useful Function Settings38 EN When this function is set to on When this function is set to OFF40 EN For ExampleLink Video This VCRTelevision VCR only Video OUT PausePreventing 42 ENEdit To Or From Another ConnectionThis VCR for recording Edit From Camcorder44 EN Camcorder for playbackEnable remote pause function Select input mode on this VCRAccess Main Menu screen on this VCR Select Edit for Picture ControlTurn on the TV TV Brand Setting46 EN Set TV brand codeEnter cable box brand code Cable Box Brand SettingTurn on the cable box Operate cable boxTurn on the DBS receiver DBS Receiver Brand Setting48 EN Enter DBS receiver brand codePlug in VCR Remote Control CodeUnplug VCR Turn on VCRTroubleshooting 50 ENTimer Recording Other Problems 52 ENCan the VCR indefinitely remain in still mode? What happens if the tape reaches its end during recording?List of terms 54 ENVCR PLUS+ Record Front panel1Still Play Slow Record PauseRear panel1 56 EN78Tape speed indication How to use the Remote 5496783Full-Size VHS 30 ST-30 58 ENUsable cassettes Compact VHS* TC-20 ST-C20 TC-30 ST-C30 TC-40 ST-C40HOW to Locate Your JVC Service Center Limited Warranty 60 ENMemo 62 EN Page HR-VP78U