JVC HR-VP830U Cable Box Control, Situate Controller, Attach Controller, Connect Cable BOX to VCR

Page 15

Cable Box Control

Suggested Location

15

This procedure is required if you receive your TV channels through a cable box (descrambler). The Controller allows the VCR to automatically switch the cable box channel during timer-recording. The Controller is effective for recording shows that have been programmed using VCR Plus+ (pg. 44) or On-Screen Timer Programming (pg. 46).

Situate And Connect

Controller

Place the cable box on top of the VCR. Attach the VCR's Controller to the top of the VCR with the Controller’s transmitter pointed towards the cable box’s remote sensor.

Attention:

The Controller can also control a DSS receiver. If both a cable box and a DSS receiver are used, position the controller so its signal reaches the remote control sensors of both the cable box and DSS receiver.

Cable box

Your VCR

Controller (suggested locations)

Cable box

Controller

 

 

Transmitter

 

 

 

 

 

Connected

 

 

 

 

 

 

 

 

Connected to

to VIDEO/

 

 

ANT. IN

AUDIO IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Your VCR

CABLE

BOX

SITUATE CONTROLLER

1 Place the Controller so that the path between its transmitter and the cable box’s remote sensor is unobstructed.

ATTACH CONTROLLER

2 Fasten securely using the supplied adhesive strips.

CONNECT CABLE BOX TO VCR

3 The connection method depends on the type of cable box you have.

If your cable box has AUDIO and VIDEO OUT connectors . . .

. . . connect them to the AUDIO and VIDEO IN connectors on your VCR.

If your cable box doesn’t have AUDIO and VIDEO OUT connectors . . .

. . . connect the antenna output connector on the cable box to the ANT.IN connector on the rear of your VCR. Set the VCR tuner to the same channel as the cable box RF output (see page 17 also).

NOTE:

Refer to your cable box’s instruction manual during connection.

CONNECT CONTROLLER TO VCR

4 Connect to the CABLE BOX connector on your VCR.

About Your Cable Box

This VCR has two separate methods to control your Cable Box.

The VCR's Wireless Remote Control Unit can control your Cable Box.

This eliminates the need for a separate Cable Box Remote Control Unit.

The VCR's Controller can also control your Cable Box.

This allows the VCR to change your Cable Box's channel number during timer recording.

Each method must be set up separately. To set up the VCR's Remote Control unit, refer to page 61. To set up the Controller go to page 16.

Image 15
Contents HR-VP830U Do not place the VCR Dear CustomerGrounding or Polarization Power SourcesPower Cord Protection Power LinesReplacement Parts AccessoriesDamage Requiring Service CleaningContents Basic Connections Auto Clock Set/Auto Tuner Set Initial SettingsDual Quick Set Perform Dual Quick SETTurn on the VCR Access ON-SCREEN MenuAccess Custom SET Screen LanguageClock PreparationOverride Auto Semi-Auto Access Select ScreensSelect Host Channel Select Time ZoneMake Corrections Select D.S.T. ModeSelect Mode SET DATE, Time and D.S.TTuner Return to Normal Screen Perform Auto Channel SETStore Desired Channel Access Tuner SET ScreenAccess AFC Screen Make SelectionConnect Cable BOX to VCR Cable Box ControlSituate Controller Attach ControllerSET, then press OK Press CH5 or TimeScan 5 to place Arrow next to CustomSet Cable Box Brand Access Cable BOXTurn on Cable BOX Brand SET ScreenBrand Code You can now set up the VCR Plus+ feature pgSpecial Notes for Cable Subscribers VCR Plus+ SetupAccess Main Menu Screen Channel Number MatchingPress CH5, Time Scan ProcedureScan 5 to place Arrow next to Guide Channel SET, thenCheck Input Data Input Receiving Channel NumberController Transmitter Connected to DSS Receiver ControlConnect DSS Receiver to VCR DSS receiverSet DSS Receiver Output Channel Return to Custom SET ScreenTurn on DSS Receiver Enter DSS Receiver BrandSet DSS Receiver Brand Start Playback Simple PlaybackLoad a Cassette Find Program Start PointSimple Recording Still Picture/Frame-By- Frame Playback Pause During PlaybackActivate FRAME-BY Frame Playback Playback and Recording FEA TuresTracking Tracking ModeAdjust Manual Engage ManualSelect The Soundtrack Superimpose Manual Index Mark/Erase Access Distant CodeStart Search Index SearchReturn to Counter Position Zero Activate Instant ReviewActivate Counter MemoryAV Compu Link Playback Tape Position IndicatorMake Connection Next-Function MemoryAccess Function SET Screen Variable-Speed Search/ Reverse Play TimeScanActivate HIGH-SPEED Search High-Speed Search 7x playbackSkip Search Skip Over Unwanted SectionsTimeScan Audio Timescan Audio byOr Time Active Video Calibration Begins with the picture level optimized RecordingVCR takes about Seconds to assess Quality of the tape Use, then recordingTape in use PlaybackDisplay Elapsed Time on Screen Engage TV ModeReset Counter to Zero Select Channel for ViewingStereo And SAP Second Audio Program Access Function SETAccess 2ND Audio Return to NormalAccess HI-FI REC Level Adjust Audio RecordING Level Enter Pluscode Number VCR Plus+ Timer ProgrammingAccess VCR PLUS+ Screen When Using The Illumi-Guide FeaturePress SP/EP Engage Timer ModePress TIMER. The VCR turns off automatically CHECK/CORRECT Input DataOn-Screen Access ON-SCREENAccess Program SET Timer RecordingOn channel 40 from 1200 noon To 100 PM in SP mode, If you program the VCR to timerSET Program Information Record a show on SeptemberCheck And Cancel Programs Disengage TimerCancel a Program RE-ENGAGE TimerOr, during on-screen timer programming Access Auto Timer ScreenAccess Auto Timer Auto TimerPress REC on the front panel Instant Timer Recording ITREngage ITR Mode SET Recording DurationEdit To Or From Another Mode Access SpecialEdit From a Camcorder SET RECORDER’S InputSelect Input Access AUX Input ScreenSet the camcorder to its play mode Set your VCR to its record modeAssemble Editing Start Dubbing SET Input ModeLocate Start Point Engage Audio DubbingLocate END Point Reset the CounterEND Insert Editing Engage Insert EditingCH5 or Time SCAN5 Random As- semble EditingPrepare for Editing Load Source CassettePrepare Recording Deck Locate EDIT-IN PointLocate EDIT-OUT Point Start R.A. EditOperate TV SET Remote Control ModeTurn on the TV SET TV Brand CodeOperate Cable BOX Cable Box Multi-Brand Remote ControlTurn on the Cable BOX Enter Cable BOX BrandTurn VCR Power on Unplug Vcrs PowerSET A/B Code Switch Plug in Power CordMake sure the window side is up, TroubleshootingSymptom Cassette gets stuck partwayOubleshooting Timer againRe-perform the VCR Plus+ setup Doesn’t work properly When scanning channels, someResume recording Remote control won’t operate What happens if the tape runs out during recording? Questions and AnswersCan the VCR indefinitely remain in the still mode? Can the VCR indefinitely remain in the Record-Pause mode?List Of Terms MBR Multi-Brand Remote Code SettingVCR Plus+ Timer Programming IndexFront View Front Display Panel Remote Control ProvidedFrequency-synthesized tuner EIA monochrome signal20C to 60C -4F to140F Maximum recording timeFor Servicing HOW to Locate Your JVC Service CenterLimited Warranty WarrantyMemo EMO Page HR-VP830U