JVC HR-E939EG Enter Showview Number, Close Menu, When Using a Satellite Tuner, Preparation

Page 23

 

ENTER SHOWVIEW

 

 

NUMBER

 

 

 

Press OK, and a cursor

 

 

 

appears above “GUIDE

12345 5

 

4 PROG”. Then, using the

 

GUIDE PROG TV PROG

 

NUMBER keys, input the

 

 

 

ShowView number (found

1

1

 

in most TV listings) of a

 

 

 

program scheduled to be

[0 – 9] =

 

 

broadcast on each station

 

 

 

on the list from step 1,

When entering a ShowView

 

starting at the top. If you

number for ARD

 

 

enter the wrong number,

 

 

 

press CANCEL and input the correct number.

 

 

ENTER CHANNEL POSITION

 

NUMBER

 

 

4

Press OK and the display

 

 

under “TV PROG” begins

 

 

 

 

 

 

5 blinking.

GUIDE PROG TV PROG

 

250

39

If the blinking number under “TV PROG” agrees with the channel

position . . .[5°] =

. . . press OK.

If the numbers do not agree . . .

. . . input the channel position using PUSH JOG%Þ or the NUMBER keys, then press OK.

●If you input the ShowView number of a program that has already aired, “ERROR” appears on screen for a few seconds. Input the correct ShowView number.

●Repeat steps 4 and 5 as necessary.

CLOSE MENU

6 Press CH SET and selection is complete.

If you already know the Guide Prog. number for a station . . .

1– After step 3, press PUSH JOG %.

●The GUIDE PROG number begins blinking.

2– Enter the Guide Prog. number using the NUMBER keys or PUSH JOG%Þ, then press PUSH JOG %.

●The TV PROG number begins blinking.

3– Enter the channel position using the NUMBER keys or PUSH JOG%Þ, then press PUSH JOG% .

●Repeat 2 and 3 as necessary. 4– Press CH SET.

EN23

When Using A Satellite

Tuner

Satellite Antenna

Aerial or Cable

Ex. 1

Ex. 2

 

 

 

Satellite

Satellite

 

Tuner and

 

Tuner

 

Decoder

 

 

 

AV2 IN/DECODER

 

 

AV2 SELECT Switch

TV Receiver

Preparation

1– Connect the satellite tuner to the AV2 IN/DECODER connector on the rear of your recorder.

2– Set the AV2 SELECT switch to "AV2".

To Record Satellite Broadcasts . . .

1– Select the appropriate channel on the satellite tuner.

2– Press NUMBER key "0" to set your recorder's input mode to "AUX2".

3– Start recording (☞ pg. 16, steps 3 – 6).

To Record Satellite Broadcasts Using ShowView Timer Recording . . .

1– Perform Guide Prog. Number setting.

●In step 5 in the left column, press NUMBER key "0" to set "TV PROG" to "AUX2".

2– Perform ShowView Timer Recording (☞ pg. 24).

To Record Satellite Broadcasts Using Regular Timer Recording . . .

1– In step 6 on page 26, press TV PROG. +/– to set the channel position to "AUX2".

NOTES:

●When timer-recording a satellite programme, first set the satellite tuner to the appropriate channel before the selected programme begins and then set the satellite tuner's timer. If your satellite tuner does not have a timer, leave it switched on.

●If your recorder's front panel VIDEO and/or AUDIO connec- tors are being used, they take priority and "AUX2" cannot be selected. Make sure no cables are connected to the front panel connectors when performing this procedure.

Page 22 Page 24
Image 23
Page 22 Page 24
Contents HR-E939EG/EH Do not place the recorder Safety PrecautionsFor Italy Tune The TV To Your Video Recorder BasicConnections Connecting Using a Decoder Select Country Access Language ScreenTuner Set Select LanguageReturn to Normal Screen EN Initial SettingsFine tuning is performed automatically when you select View Confirmation ScreenPreparation Clock SetTurn the Recorder on SET Date and Time SET ClockReturn to Normal ScreenStart Playback PlaybackLoad a Cassette PointActivate HIGH-SPEED Search Playback FeaturesPause During Playback Activate Instant Review Adjust TrackingOverride Automatic Tracking ManuallyEN Playback Activate Scene FinderStop Scene Finder Activate Index SearchMemory SET A/B Code SwitchRE-SUPPLY Power Activate CounterVariable-Speed Search/ Reverse Play Audio signal during TimeScanTime Scan Shuttle Indicator Time Scan Indicator TimeScanAudio output TimeScanSpeed SP Speed LP Recording Confirm B.E.S.T. Status Access Mode SelectS.T. Picture SystemPlayback ON-SCREEN Display ENABLE/DISABLEClose Mode Select On-Screen Displays To Record Stereo And Bilin- gual Programmes A2 Recording Features EN Recording Receiving Stereo And Bilin- gual ProgrammesSelect Channel to Watch Reset CounterEngage ITR Mode LevelMake List of Stored Station Names Channel Positions Access CH. SET Mode Menu ScreenEN Timer Recording Information On ShowViewPreparation When Using a Satellite TunerEnter Showview Number Close MenuWhen Using The Illumi-Guide Feature ShowView Timer RecordingEN Timer RECORDINGcont Access Timer PROGRAM- Ming ScreenEngage RECORDER’S Timer ModeAccess Showview Program Screen Enter Programme Start Time Regular Timer ProgrammingAccess Programme Screen Screen Engage RECORDER’S Timer ModeTime Enter Channel PositionEngage Auto SP/LP Access Programme ScreenTimer Revise Programme IN- FormationTRY Operating TV Multi-Brand Remote ControlRemote Control EN SET TV Brand CodeStart Source Player SET Recording DECK’S Input ModeEdit To Or From Another Video Recorder Make ConnectionsStart Recorder SET RECORDER’S Input ModeEdit From a Camcorder Start CamcorderSemble Editing Random AsPrepare Recording Deck Locate EDIT-OUT PointStart R.A. Edit END R.A. EditLocate END Point SET Input ModeReset the Counter Locate Start PointEND Insert Editing Engage Insert EditingStart Editing END Audio Dubbing Audio DubbingEngage Audio Dubbing Start DubbingPause Select Position Access CH. SET ModeSelect Mode MenuSelect NEW Station Switch StationsAccess Manual CH. SET Perform TuningStation Name Clear Troubleshooting E NOubleshooting Timer againQuestions and Answer S Ä remain lit on the display panel. Is there a problem?44 EN Open the lid to access covered connectors and buttonsRear View Indicator will blink during turbo searchE R Installing BatteriesHow To Use IndexMaximum recording time RCA connectors VideoSpeci Fications EN HR-E939EG/EH
Top Page Image Contents