JVC HR-E939EG Locate EDIT-OUT Point, Start R.A. Edit, END R.A. Edit, Prepare Recording Deck

LOCATE EDIT-OUT POINT

EN33

NOTES:

● You can also monitor the sound when searching for scenes

7

Find the point where you want the edited scene to end by pressing PUSH JOG Þ %or using the TIME SCAN SHUTTLE ring or the JOG dial, then press IN/ OUT.

=1 0:02:23 2

3

4

5

6

7

8

0:02:23

(+) 0:00:00

you want to edit in steps 6 – 7. Since you can hear the soundtrack during selection, you can avoid abrupt or unnatural sounding scene-to-scene transitions. The sound that is heard, however, is not TimeScan Audio.

● When editing, there may be a discrepancy of about 2 seconds on the source tape between the locations you chose as edit-in/-out points and the locations your recorder recognizes as those points.

● For any scene, the edit-out point must have a counter reading

●The edit-out point is registered in memory and appears on the screen.

●The total time of the edited scenes is displayed to the right of "(+)".

●Repeat steps 6 and 7 for each additional scene.

1 0:02:23 0:02:51

=2 3 4 5 6 7 8

0:02:51

(+) 0:00:28

that is at least 1 second after the corresponding edit-in point. Any less than 1 second and the edit-out point will not be registered.

● Since the source recorder prerolls during Random Assemble Editing, there must be at least 15 seconds worth of recorded material prior to any edit-in point on the source tape.

● If the search time for an edit-in point exceeds 5 minutes, the recording deck enters its Stop mode and editing will not take place.

● During steps 6 and 7 — if you engage the Pause mode while registering edit-in and -out points in the R.A. Edit screen, the characters in the on-screen display may become distorted. This

8

9

PREPARE RECORDING DECK

Engage its Record-Standby mode.

START R.A. EDIT

Press START.

● Automatic editing begins; all the specified scenes are

copied to the recording deck in the order they were

registered.

● The on-screen display remains while your recorder

is normal.

To Make Corrections . . .

. . . during step 6 or 7, you can cancel registered in and out points by pressing CANCEL on the remote control. Each time you press, the preceding point is erased.

● If, for example, you have registered 5 sets of in and out points and want to reset the first set, you have to press CANCEL until all points after the first set have been erased. Reenter them after you've repaired the first set of points.

searches for each scene (blinking cursor indicates

scene currently being searched for), but disappears

during actual editing.

● During scene search, the recording deck automati-

cally enters its Record-Standby mode.

● When all registered scenes have been edited, your

recorder enters the Pause mode, the recording deck

enters its Record-Standby mode, and the cursor blinks

at the next available number.

Memory Capacity

Random Assemble Editing shares memory space with the recorder's timer. If there are programs occupied by timer-recording data, those spaces cannot be used to register edit-in and -out points — meaning you won't be able to edit 8 scenes.

PROGRAM FULL

0:00:00

(+) 0:00:00

10

END R.A. EDIT

Press R.A. EDIT again, and engage the Stop mode for your recorder and for the recording deck.

●When all 8 programs are full, "PROGRAM FULL" appears on the R.A. EDIT screen.

●To cancel a program, see page 28.

RM-V704U Multi-Brand R.A. Edit Controller (Not provided)

By connecting this controller to your recorder's R.A. EDIT connector, you can perform Random Assemble Editing in combination with a second non-JVC video recorder. The controller is compatible with various major recorder brands. For compatible systems and availability, please consult your JVC dealer.

NOTE:

Although the RM-V704U is designed to operate the recording deck, it may not work with some recorders, or may have limited function capability.