Recording method, Recording Audio dubbing | JVC BR-DV3000E instruction

RECORDING

– Recording method –

RECORDING – Audio dubbing –

Remote controller

3.2.

PAUSE button REC button

Main unit

2.	2. 4.
REC	PLAY
button	button

For tapes recorded in the 32kHz audio mode, audio dubbing can be performed on the CH3 and CH4 channel after the recording. (After-recording)

Notes

•For tapes recorded in the 48kHz audio mode, audio dubbing cannot be performed.

•Audio dubbing cannot be performed for DV input signals.

2.	4.	A.DUB	PAUSE	REC
2.	4.
PLAY		F.REV	PLAY	F.ADV
PLAY			PLAY
button
		REW		FF

OPERATE

Mini

A.DUB

		EJECT
		MENIU
REC	PLAY	PAUSE

3. A.DUB button

2. 3.

PAUSE button

3.	A.DUB button

1. 4.

PLAY button

5.		STOP
5.
STOP	INDEX–	INDEX+
STOP	REMOTE CONTROL UNIT
button		RM-G3000
button

PROFESSIONAL
MIC	REMOTE SEL.	INPUT SEL.
	SERIAL	LINE
	9PIN WIRELESS	DV Y/C

DVCAM NTSC PAL REC INH.
CH-1/3		SET
REW	STOP	FF
CH-2/4
BR-DV3000

3. PAUSE button

1. 4. PLAY button

A.DUB	PAUSE	REC
F.REV	PLAY	F.ADV
	PLAY

OPERATE

EJECT

MENIU

Memo

5.	STOP button

1.	Load the cassette.

5. STOP button

REW	FF
	STOP
INDEX–	INDEX+

REMOTE CONTROL UNIT

RM-G3000

	Mini	A.DUB
PROFESSIONAL
MIC	REMOTE SEL.	INPUT SEL.
	SERIAL	LINE
	9PIN WIRELESS	DV Y/C

DVCAM NTSC PAL REC INH.

CH-1/3

CH-2/4

BR-DV3000

REC	PLAY	PAUSE
			2. 3.
REW		SET	PAUSE
REW	STOP	FF	PAUSE
			button

•If recording has been paused for an extended pe- riod of time, the unit will au- tomatically go into the STOP mode to protect the tape. The time period after the lapse of which the unit will enter the STOP mode can be configured via the LONG PAUSE TIME item of the SYSTEM (1/2) menu.

•This unit cannot perform editing functions.

•Before loading the cassette, please check that the rear slide of the cassette is pushed to REC.

¥ The Main unit is powered on.

2.Start recording.

•Hold down the REC button and press the PLAY button.

3.Pause recording.

•Press the PAUSE button.

4.Resume recording.

•Press the PLAY button.

5.Stop recording.

•Press the STOP button.

MIC terminal

Connection

Audio dubbing sounds are input from the AUDIO IN terminal on the rear panel or the MIC terminal on the front panel. MIC terminal prevail over the AU- DIO IN terminal.

Setting

•Set the AUDIO item of the AUDIO/VIDEO menu to 32k.

•Do not set the INPUT SEL switch on the front panel to DV.

Operation

INPUT SEL switch	5. STOP button
Memo

•During audio dubbing, if the tape comes to a part recorded in a non dubbing-feasible mode (such as LP mode or 48kHz audio mode), the VTR will enter the STOP mode. When this hap- pens, high-volume noise from the DV output will occur. Hence, before audio-dubbing, please check the recording mode of the tape.

•In the case that a microphone is connected to the MIC terminal, sound output from this ter- minal will be recorded. In the absence of MIC input, signals from the CH1/3, CH2/4 AUDIO IN terminal on the rear panel will be recorded.

•When audio dubbing cannot be performed, an alarm message will be displayed on the moni-

tor. ( ☞ Page 23)

Memo

If recording is executed right after the RECORDING PAUSE state, index signals will not be recorded.

Recording index signals

When the INDEX WRITE item of the SYSTEM (1/2) menu is set as ON, an index signal is recorded at the starting position of recording. In the PLAYBACK mode, the position where the index signal is recorded can be detected. (Index search)

During recording, please press the REC button to record the index signal.

*Please allow at least an interval of 1 minute between recording of index signals.

Recording of index signals after tape recording is not possible.

1.	Press the PLAY button to play the tape.
2.	At the position where you want to au-
	dio dub, press the PAUSE button.
3.	¥ The unit goes into the STILL mode.
3.	Hold down the PAUSE button and press
	the A.DUB button.
	¥ The unit goes into the audio dubbing pause
	mode.
4.	Press the PLAY button.
	¥ Audio dubbing begins. Audio signals are
	recorded on the CH3 and CH4 channel.

To stop audio dubbing temporarily, press the PAUSE button.

5.	To end audio dubbing, press the STOP
	button.

•Audio dubbing PAUSE cannot be executed di- rectly in the STOP mode. Please execute it in the STILL mode.

During audio dubbing pause, sound from the CH3/CH4 channel is output via the monitor but sound output from the DV terminal is not pos- sible.

•If audio dubbing is repeated on a short section of the tape, noise may occur for an instant when the section is played.

•During audio dubbing, noise may be produced on the playback video or EE sound but the re- cording is normal.

•The playback sound of CH1/2 cannot be re- corded on CH3/4 (sound on sound).

•During backspace operation of audio dubbing, audio dubbing cannot be performed on unre- corded parts.

•When audio dubbing is performed on tapes re- corded on other devices, it may not record cor- rectly. Please record with this unit before per- forming audio dubbing.