Magnavox MVR430MG, MVR630MG owner manual Timer Recording cont’d, Instructions continue on

Page 29

mvr630mg.QX33 2/11/02 12:05 PM Page 29

Timer Recording (cont’d) 29

4 Use the Number buttons (1-8) to select a slot in which to store the timer recording. There are eight slots. Numbers for open slots will flash on the screen.

NOTE: If you enter a number for a slot that has already been used to store a timer recording, PREVIOUSLY SET PROGRAM will appear on the screen briefly. Information about the program in that slot will appear on the screen. If this happens, press the STATUS/EXIT but- ton, then select another number.

5 Use the Number buttons to enter the channel you want to record.

● Cable Users, enter channel numbers as a two-digit number for the quickest results. For example, to select channel 6, press 0,6. If you only press the Number 6 button, channel 6

POWER VCR/TV EJECT

REW4-7

will be selected after a brief delay. There also may be a brief delay when you select channels 10, 11, and 12. If you want to select channels 100 and above, enter channel numbers as a three-digit number. For example, to select channel 117, press 1, 1, 7.

Antenna Users, enter channel numbers as a two-digit num- ber for the quickest results. For example, to select channel 5,

STATUS/EXIT

1 2 3

4 5 6

7 8 9

0

CH

press 0,5. If you only press the Number 5 button, channel 5 will be selected after a brief delay. You may only select channels 2-69.

●If you are recording from line input, press 0,0 to select AV REAR.

●If you are using a Cable Box/DBS, enter the Cable Box/DBS output channel (03 or 04). Set the Cable Box/DBS to the channel you want to record. Leave the Cable Box/DBS on for the timer recording. See page 8 for details.

6 Press two Number buttons for the hour you want the recording to begin. Press two Number buttons for the minute you want the recording to begin.

Press 1 for AM or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

SPEED TIME SEARCH STILL/PAUSE

REC/OTR MEMORY SLOW

7 Follow the instructions in step 6 to enter the record- ing’s stop time. (AM or PM will be set automatically.)

ONE TIME PROGRAM

PROGRAM

1

CHANNEL

10

TIME ON

09:30 PM

TIME OFF

– – : – –

TO CORRECT PUSH CLEAR

TO END PUSH EXIT

Instructions continue on page 30.

Helpful Hints

•Entries that do not match the VCR’s clock or calendar will cause a ques- tion mark to appear on the screen.

•If you are recording from line input, connect the audio and video cables to the AUDIO IN and VIDEO IN jacks on the back of the VCR. (Please see illustration on page 32.)

Page 28 Page 30
Image 29
Page 28 Page 30
Contents MVR430MG/MVR630MG VCR Dear Magnavox product owner Warranty VerificationTable of Contents Safety Precautions FeaturesIntroduction Declaration of ConformityPutting Batteries in the Remote Control Before Using Your VCRBattery Safety VCR maintenanceDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemCH3 CH4 Recording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Recording One Channel/Watching Another Signal RF coaxial cable TV’s AntennaConnect a Cable signal to the VCR’s ANTenna in Jack MVR630MG Hookups with a Stereo TVPress the Menu button. The display shown below will appear Correctly. Details are on pagesMVR630MG only Automatic Channel SetupPress the Menu button Adding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsVCR may lose the clock setting if the power fails Setting the ClockButton Enter a 0 before a single-digit numberDaylight-Savings Time Press the STATUS/EXIT button Language SelectionRemote Control Buttons CHannel o/p Button Remote Control Buttons cont’dIf you select Status OFF If you select Status ON, then select Counter only onIf you select Status ON, then select Counter only OFF VCR Display Panel Front Panel Rear Panel Playing Other playback options and features are on pagesRead and follow the steps below to play a tape 1Turn on the TV 2Insert a tape in the VCRRecording VCR records in a preset volumeTo stop recording, press the STOP/p button For recording options, see pagesPress the VCR/TV button to put the VCR in VCR Recording One Channel/Watching AnotherPosition. The VCR/TV light will appear on the VCR display Panel againOne-Touch Recording When the OTR finishes, the VCR shuts itself offTurn itself off Ton onceSet the clock. Details are on Timer RecordingDo each step within 60 seconds of the previous step DailyInstructions continue on Timer Recording cont’dTape Speeds This timeCassette type/Playback Time Tape Speed T160 T120 T60Checking or Cancelling Timer Recordings Make the connections shown above Rerecording Tape DuplicationVCR 1 will play your tape. Put a prerecorded tape VCRRepeat Play Press the PLAY/o button to watch the tape Real-Time Counter MemoryPress the Time Search button Time SearchForward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Monitor Understanding On-Screen DisplaysOr Receiver Monaural SoundMulti-Channel Television Sound System MVR630MG only cont’d Please see additional notes on Hi-Fi Stereo Sound System MVR630MG onlyBlue Background Helpful Hints Helpful Hints cont’d Product sold AS is or Renewed Shipping charges to return defective productContact Magnavox Customer Care Center at English or Spanish SpeakingGlossary Glossary / SpecificationsSpecifications Timer Record PowerRemote control Audio in/out jacksSupplied Accessories
Top Page Image Contents