Magnavox MVR430MG, MVR630MG owner manual Correctly. Details are on pages

Page 11

mvr630mg.QX33 2/11/02 12:05 PM Page 11

 

Turning on Your VCR 11

Before turning on your VCR, make sure batteries are in the

2 Turn on the TV.

remote control and you have connected the VCR and TV

correctly. Details are on pages 5-10.

●You can not program channels if you are using a Cable Box or a Direct Broadcast System.

1

2

Press the POWER button. The VCR/TV light and the POWER light will appear on the VCR display panel.

Turn on the TV. Set it to the same channel as the CH3/CH4 switch on the back of the VCR. The display shown below will appear on the TV screen. (If the display does not appear, check your hookups, then follow the steps on page 12 to set up channels and page 17 to select a lan- guage.)

1

4

POWER VCR/TV EJECT

 

 

PLAY

 

 

REW

 

 

 

F.FWD

 

 

STOP

 

 

MENU

 

STATUS/EXIT

 

CLEAR

 

 

 

 

1

2

 

3

 

4

5

 

6

CH

 

 

7 8 9

3

5

SELECT op

0

→ ENGLISH

ON

ESPAÑOL

 

SPEED TIME SEARCH STILL/PAUSE

REC/OTR MEMORY SLOW

MAKE SELECTION OR

PUSH MENU TO CONTINUE

3 Within 60 seconds, press the PLAY/o button or the STOP/p button to select English or Spanish on- screen displays and menus.

4 Press the MENU button. The display shown below will appear.

CONNECT ANTENNA OR CABLE

TO VCR

THEN . . .

PUSH CH UP KEY

OR . . .

FOR PLAY ONLY – PUSH STOP

5 Within 60 seconds, press the CH(annel) o button to begin automatic channel programming. AUTO CH PROGRAMMING IN PROCESS PLEASE WAIT will appear on the TV screen. The VCR will memorize all available channels. When all channels are memorized, CHANNELS ARE SET will appear on the TV screen briefly, then TV programming will appear.

Now, when you press the CH(annel) o/p button, you’ll only scan through channels that you receive. You can still select other channel numbers using the Number buttons.

Helpful Hints

•To skip this feature and play a tape immediately, insert a tape with its record tab removed. Or, to skip step 3, press the MENU button. All on- screen displays will be in English. To skip step 5, press the STOP/p but- ton. Channels will not be pro- grammed, and CHANNELS NOT SET will appear on the screen.

•If you try to program channels when there is no antenna or cable connected to the VCR, programming will appear to take place, but even- tually a NO TV SIGNALS message will appear. Connect an antenna or cable to the VCR’s ANT(enna) IN Jack and press the CH(annel) o button again. You may need to fol- low the steps on page 12.

•You may need to repeat the steps on this page if a power failure occurs.

•If you used the AUDIO and VIDEO OUT jacks to connect the VCR to the TV, see page 10. You need to choose a channel other than 3 or 4 at the TV to see the VCR image on your TV.

Page 10 Page 12
Image 11
Page 10 Page 12
Contents MVR430MG/MVR630MG VCR Dear Magnavox product owner Warranty VerificationTable of Contents Declaration of Conformity FeaturesSafety Precautions IntroductionVCR maintenance Before Using Your VCRPutting Batteries in the Remote Control Battery SafetyDisconnect the antenna or cable from your TV Hookups Without a Cable Box/Direct Broadcast SystemCH3 CH4 Recording/Viewing Any Channel Hookups With a Cable Box/Direct Broadcast SystemConnections Recording One Channel/Watching Another Signal RF coaxial cable TV’s AntennaConnect a Cable signal to the VCR’s ANTenna in Jack MVR630MG Hookups with a Stereo TVPress the Menu button. The display shown below will appear Correctly. Details are on pagesMVR630MG only Automatic Channel SetupPress the Menu button Adding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsEnter a 0 before a single-digit number Setting the ClockVCR may lose the clock setting if the power fails ButtonDaylight-Savings Time Press the STATUS/EXIT button Language SelectionRemote Control Buttons CHannel o/p Button Remote Control Buttons cont’dIf you select Status OFF If you select Status ON, then select Counter only onIf you select Status ON, then select Counter only OFF VCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR Other playback options and features are on pagesPlaying Read and follow the steps below to play a tapeFor recording options, see pages VCR records in a preset volumeRecording To stop recording, press the STOP/p buttonPanel again Recording One Channel/Watching AnotherPress the VCR/TV button to put the VCR in VCR Position. The VCR/TV light will appear on the VCR displayTon once When the OTR finishes, the VCR shuts itself offOne-Touch Recording Turn itself offDaily Timer RecordingSet the clock. Details are on Do each step within 60 seconds of the previous stepInstructions continue on Timer Recording cont’dTape Speed T160 T120 T60 This timeTape Speeds Cassette type/Playback TimeChecking or Cancelling Timer Recordings VCR Rerecording Tape DuplicationMake the connections shown above VCR 1 will play your tape. Put a prerecorded tapeRepeat Play Press the PLAY/o button to watch the tape Real-Time Counter MemoryPress the Time Search button Time SearchViewing a Still Picture Special Effects PlaybackForward and Reverse Searching SP/LP/SLP Super High Speed Searching LP/SLPAutomatic Operation Features Monaural Sound Understanding On-Screen DisplaysMonitor Or ReceiverMulti-Channel Television Sound System MVR630MG only cont’d Please see additional notes on Hi-Fi Stereo Sound System MVR630MG onlyBlue Background Helpful Hints Helpful Hints cont’d English or Spanish Speaking Shipping charges to return defective productProduct sold AS is or Renewed Contact Magnavox Customer Care Center atGlossary Glossary / SpecificationsSpecifications Audio in/out jacks PowerTimer Record Remote controlSupplied Accessories
Top Page Image Contents