Preparation for First Time Usage
Turn on the unit for the first time
VCR
VCR
1
Turn on the TV and set it to channel 3.
•If channel 3 is already occupied for broadcasting, see“RF Output Channel” section.
To Preset the Channel Again
1)Press the MENU button until the main menu appears.
2)Select "CHANNEL SET UP" by pressing the K or L button. Then, press the B but- ton.
3)Select "AUTO SET UP" by pressing the
K or L button. Then, press the B button. After scanning, the tuner stops on the low- est memorized channel.
4 |
| CLOCK SET | |
| MONTH DAY | YEAR | |
or | 0 3 | / 1 5 | 2 0 0 4 |
|
|
| |
| HOUR MINUTE | AM/PM | |
| – – | : – – | – – |
| Select the current year | ||
2 | POWER | TV Screen |
|
|
| ||
|
| LANGUAGE SELECT | |
|
| B ENGLISH | [ON] |
| or | FRANÇAIS |
|
|
|
| |
Setup |
| ESPAÑOL |
|
|
|
| |
3 |
|
| CH 01 |
AUTO SET UP
Do you connect the cable from the cable box or the satellite box to the DVD/VCR’s ANT IN jack?
YES
Yes Press the MENU button to exit
•Refer to “Tips for Cable Box or Satellite Box” section on
page 6. | NO |
No Please wait for a few minutes.
After scanning...
•The tuner stops on the lowest memorized channel.
•You can select only the channels memo- rized in this unit by using the CHANNEL buttons.
•If "AUTO SET UP" appears on the TV screen again, check the cable connections. Then, press the B button once again.
Tips
•Repeat these steps only if either there was a power failure or this unit has been unplugged for more than 30 seconds.
To Change the On-Screen Language
1)Press the MENU button until the main menu appears.
2)Select "LANGUAGE SELECT" by press- ing the K or L button. Then, press the B button.
3)Select "ENGLISH" , "FRANÇAIS" or "ESPAÑOL" by pressing the K or L but- ton. Then, press the CLEAR/C.RESET button.
Tips
•If you accidentally select Spanish or French and need English: Press the MENU button and choose SELEC.
IDIOMA, or SELECTION LANGUE. Press the B button, and select ENGLISH. Finally, press the CLEAR/C.RESET button.
Clock Set Up
| VCR |
VCR |
|
1 MENU |
TIMER PROGRAMMING
AUTO REPEAT [OFF]
CHANNEL SET UP
BCLOCK SET LANGUAGE SELECT AUDIO OUT
| TV STEREO [ON] |
| SAP |
or | • If the clock is not set, the |
| CLOCK SET screen |
| appears when you press |
| the MENU button. In this |
| case, go to step [2]. |
2 |
| CLOCK SET | |
or | MONTH DAY | YEAR | |
0 3 | / – – | – – – – | |
| HOUR MINUTE | AM/PM | |
| – – | : – – | – – |
| Select the current month | ||
5 | CLOCK SET | |
MONTH DAY | YEAR | |
0 3 | / 1 5 MON 2 0 0 4 | |
or |
|
|
HOUR MINUTE | AM/PM | |
0 5 | : – – | – – |
Select the current hour | ||
6 | CLOCK SET | |
MONTH DAY | YEAR | |
0 3 | / 1 5 MON 2 0 0 4 | |
or |
|
|
HOUR MINUTE | AM/PM | |
0 5 | : 4 0 | – – |
Select the current minute | ||
7 | CLOCK SET | |
MONTH DAY | YEAR | |
0 3 | / 1 5 MON 2 0 0 4 | |
or |
|
|
HOUR MINUTE | AM/PM | |
0 5 | : 4 0 | P M AM |
|
| B PM |
Select “AM” or “PM” | ||
8To exit the CLOCK SET screen.
Tips
• To go back one step, press the s button |
(during the steps [2] to [7].) |
• Your clock setting will be lost if either there |
is a power failure or this unit has been |
To Select a Channel
You can select a channel by directly entering channel using the Number but- tons on the remote control.
Notes for using the Number buttons:
•When selecting cable channels which are higher than 99, enter channel numbers as a
•You must precede
3 |
| CLOCK SET | |
| MONTH DAY | YEAR | |
or | 0 3 | / 1 5 | – – – – |
|
|
| |
| HOUR MINUTE | AM/PM | |
| – – | : – – | – – |
| Select the current day | ||
unplugged for more than 30 seconds. |
– 10 – | EN |