JVC VR-716E instruction manual Names and Functions Signal In/Out Terminal

Getting Started (continued)

Names and Functions (Signal In/Out Terminal)

(Rear)
AUDIO IN
1	2	3	4	5	6		7	8	9	10	11				12			13				14	15		16
VIDEO IN
THRU OUT
	SCSI								CAUTION
				AUDIO OUT			VIDEO OUT
									RISK OF ELECTRIC SHOCK
			LAN						DO NOT OPEN
RS-232C		UPS		1	2	1	2		AVIS:RISQUE DE CHOC
									ELECTRIQ													1	4/	16	5	8	AC IN
																											(220V–240V	)
										1	3	5	7	9	11	13	15	RST	COM	IN	IN	EXT REC					SIGNAL GND
										2	4	6	8	10	12	14	16	OUT		CLK	SER		9	12	13	16
																			WAR	RST	REC	COM
														ALARM					OUT	OUT	OUT			EE OUT

1ALARM IN

CAMERA 1, 3, 5, 7, 9, 11, 13, 15

CAMERA 2, 4, 6, 8, 10, 12, 14, 16

2ALARM RESET

3CLOCK RESET IN

4SERIES REC IN

5EXT REC IN 6COM

1	3	5	7	9	11	13	15	RST COM	IN IN EXT REC
2	4	6	8	10	12	14	16		CLK SER
								OUT WAR RST REC COM
				ALARM				OUT	OUT OUT
									7SERIES REC OUT
									8CLOCK RESET OUT
								9WARNING OUT
								0ALARM REC OUT

1[ALARM IN] Terminal (Supports Channels 1 - 16) Terminal that accepts input signals to start alarm or sensor recording.

2[ALARM RESET] Input Terminal

Terminal that accepts signals to stop recording during alarm or sensor recording.

5[EXT REC IN] Terminal

Starts recording automatically upon receiving external sig- nals when the “EXT REC MODE” is set as “TRIGGER” or “MANUAL”.

☞Page 25 ‘OPERATION/EXT REC Menu’

☞Page 61 ‘Activation of Recording Via External Signals’

3[CLOCK RESET IN] Terminal

For connection to a master clock or the [CLOCK RESET OUT] terminal of other devices. This equipment can be set to a master clock or the clock of other devices upon the input of clock reset signals.

The clock in VR-716 will be reset as follows upon the input of clock reset signals:

•When the value is 29 seconds or less, this will be reset to 00 seconds with the minute value unchanged.

•When the value is 30 seconds and above, this will be reset to 00 seconds with the minute rounded to the next higher value.

☞Page 61 ‘Series Recording Using 2 or More VR-716 Re- corders’

4[SERIES REC IN] Terminal

Series recording will start upon the input of [SERIES REC OUT] signals. This is the terminal that accepts the series recording signals of other VR-716s when multiple sets of VR-716 are used.

☞Page 61 ‘Series Recording Using 2 or More VR-716 Re- corders’

6[COM] Common Ground Terminal

This is a common ground terminal. For connection to the signal ground terminal of other devices.

7[SERIES REC OUT] Terminal

Outputs signals when the remaining hard disk space is 1 % or less.

However, there will be no signal output in the following cir- cumstances:

• When the “SERIES REC” item is set as “OFF” in the menu. ☞ Page 25 ‘OPERATION/EXT REC Menu’

☞ Page 61 ‘Series Recording Using 2 or More VR-716 Re- corders’

8[CLOCK RESET OUT] Terminal

Terminal for output of clock reset signals. Signals are out- put in the following cases:

When the internal clock of VR-716 turns 00:00 or 12:00.

☞Page 61 ‘Series Recording Using 2 or More VR-716 Re- corders’

9[WARNING OUT] Terminal

Outputs signals during hard disk malfunction or error oc- currence. (☞ Page 105)

0[ALARM REC OUT] Terminal

Outputs signals when VR-716 is in the Alarm Recording or Sensor Recording mode.

10