JVC DR-MH20B manual Basic Connections, When your TV’s Scart Set L-1 Output to Connector accepts

Place the unit on a stable, horizontal surface.

Filename [DR-MH30EU_04Name.fm]
DR-MH30EU_00.book Page 19 Thursday, June 3, 2004 11:00 AM	Masterpage:Right0

	INSTALLING YOUR NEW UNIT EN 19
Basic Connections	8 Basic Connection
	To connect to a TV with 21-pin SCART input connector —
	A Disconnect the TV aerial cable from the TV.
	B Connect the TV aerial cable to the ANTENNA IN connector on
	the rear panel of the unit.
	C Connect the ANTENNA OUT connector on the rear panel of the
	unit and the TV’s aerial connector with the provided RF cable.
	D Connect the L-1 IN/OUT connector on the rear panel of the unit
	and the TV’s 21-pin SCART connector with a provided 21-pin
	SCART cable.
TV aerial cable	● The L-1 IN/OUT connector accepts and delivers either a composite
	signal (regular video signal), Y/C signal or RGB signal.
	● Set your TV to the VIDEO (or AV), Y/C, or RGB mode according to
	the type of your TV’s SCART connector.

ANTENNA IN
COMPONENT VIDEO OUT	Mains outlet
S-VIDEO OUT	Mains power cord

8S-Video Connection

To connect to TV’s S-VIDEO input and AUDIO input connectors —

APerform A – C in “Basic Connection”.

BConnect the unit’s S-VIDEO OUT connector to the TV’s S-VIDEO input connector.

CConnect the unit’s AUDIO OUT connectors to the TV’s AUDIO

input connectors.

ANTENNA	L-1 IN/OUT
OUT

AUDIO OUT

	Component
	video cable
	(not provided)	Audio cable
		(not provided)
RF cable	21-pin SCART
(provided)	cable
	(provided)

Back of unit

S-Video cable (not provided)

●You can obtain high-quality S-VHS pictures.

●With S-VIDEO connection, you cannot use the Preset Download function. ( pg. 21)

●If your TV is not stereo-capable, use the unit’s AUDIO OUT connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction.

8Component Video Connection

To connect to TV’s component video input connectors —

APerform A – C in “Basic Connection”.

BConnect the unit’s COMPONENT VIDEO OUT connectors to

the TV’s component video input connectors.

CConnect the unit’s AUDIO OUT connectors to the TV’s AUDIO

input connectors.

● You can obtain high-quality component video pictures.

● If your TV is not stereo-capable, use the unit’s AUDIO OUT

connectors to connect to an audio amplifier for Hi-Fi stereo sound

reproduction.

● By using the component video connection, you can view the images

TV

It’s essential that your unit be properly connected.

ATTENTION:

Your TV must have a 21-pin AV input connector (SCART) for the basic connection to the unit.

THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO OPERATION CAN BE PERFORMED.

1

2 Connect the unit to a TV depending on the TV and cables you use.

in the progressive mode. For switching to the progressive mode, refer

to “Scan Mode Set” ( pg. 71).

NOTE:

Select an appropriate option of “L-1 OUTPUT” as follows ( pg. 63):

When your TV’s SCART	Set “L-1 OUTPUT” to:
connector accepts:
Composite signals	“SCART VIDEO”
Y/C signal (separated
luminance (brightness) and	“SCART S-VIDEO”
chrominance (colour) signals)
RGB signal	“SCART RGB”
Component video signal	“COMPONENT”

3 Plug the end of the mains power cord into a mains outlet.

●“LOADING” blinks on the front display panel when the AC plug of the mains power cord is connected into a mains outlet and it takes approximately 50 seconds for the unit to be turned on. This is not a malfunction.

Page 19

Thursday, 3 June 2004 10:46