JVC DR-MH30B, DR-MH20B manual Digital Audio Dubbing, Input Setting, Example Dubbing to an MD

Filename [DR-MH30EU_09Editing.fm]
DR-MH30EU_00.book Page 64 Thursday, June 3, 2004 11:00 AM	Masterpage:Left+

64 EN EDITING

NOTES:		Digital Audio Dubbing
● If you have a satellite receiver or a decoder connected to the L-2 IN/
DECODER connector, be sure to set “L-2 SELECT” back to
	You can dub selected audio from a DVD or Audio CD disc to a
appropriate mode after editing.
● If you are not connecting a satellite receiver or a decoder to the L-2	digital audio device.
IN/DECODER connector, leave “L-2 SELECT” set to “VIDEO”.	However, it is not possible to dub copy-protected discs.

●When “L-2 SELECT” is set to “SAT VIDEO” and “SAT S-VIDEO”,

“SAT” appears on the TV screen or front display panel instead of	● Turn on the TV and select the AV mode.
“L-2”.	● Slide the TV/CABLE/SAT/DVD switch to DVD.
● If “L-1 OUTPUT” is set to “SCART S-VIDEO”, it is not possible to set
	Example: Dubbing to an MD
“L-2 SELECT” to “DECODER” or “SAT VIDEO”.
● If “L-1 OUTPUT” is set to “SCART RGB”, it is not possible to set “L-2	Recorder
SELECT” to “DECODER” or “SAT S-VIDEO”.

●If “L-1 OUTPUT” is set to “COMPONENT” and “L-2 SELECT” to “SAT VIDEO”, “SAT S-VIDEO” or “DECODER”, be sure to connect the L-1 IN/OUT connector with a TV.

F-1 Input Setting

Set “F-1 INPUT” to the appropriate mode depending on the connector (VIDEO or S-VIDEO) being used on the front panel.

1 Perform steps 1 and 2 of “L-1 Output And L-1 Input Setting” ( pg. 63).

2 Press rt to select “F-1 INPUT”, then press ENTER.

3 Press rt to select the
	DVD VIDEO SET UP		HDD/DVD SET UP	FUNCTION SET UP		INITIAL SET UP
appropriate setting, then press	REC/PLAY SET UP		DISPLAY SET	VIDEO IN/OUT		CONECT
ENTER.
		MONITOR TYPE			4 : 3LB
4 Press SET UP to complete the
		F-1 INPUT
		L-1 INPUT				S-VIDEO
setting.						VIDEO
		L-1 OUTPUT			SCART VIDEO
		L-2 SELECT			VIDEO

*	The boldface settings below	SET UP	ENTER	SELECT WITH [	Player
					] THEN PRESS [ENTER]
	indicate the settings at your	EXIT	SELECT	PRESS [SET UP] TO EXIT
	purchase.

Optical cable (not provided)

Digital audio device (MD deck, etc.)

Coaxial cable (not provided)

DIGITAL OUT (COAXIAL)

8F-1 INPUT — VIDEO / S-VIDEO

VIDEO: When connecting an appliance to the VIDEO input connector, set to “VIDEO”.

S-VIDEO: When connecting an appliance to the S-VIDEO input connector, set to “S-VIDEO”.

Rear of unit

DIGITAL OUT (OPTICAL)

Note for connection:

Remove the protection cap from the cable.

1 Connect the unit and a digital audio device using either an optional optical cable or an optional coaxial cable.

2Place a disc on the unit and load an MD on the connected digital audio device.

3Select the audio to be dubbed.

4Start playback slightly before the actual point from where you wish to start dubbing.

5Press 9 to pause playback.

6Select the input mode on the connected digital audio device.

7Press 4 to start playback on the unit.

8Start recording on the digital audio device.

9Stop recording on the digital audio device. Then press 8 to stop playback on the unit.

NOTE:

There may be a discrepancy of several seconds between where you intend editing to start, and where it actually starts.

Page 64

Thursday, 3 June 2004 10:46