JVC DR-MH30B, DR-MH20B manual DV Dubbing HDD Deck Only, To skip unwanted part of the source picture

Filename [DR-MH30EU_09Editing.fm]
DR-MH30EU_00.book Page 60 Thursday, June 3, 2004 11:00 AM	Masterpage:Left+

60 EN EDITING

	DV Dubbing (HDD Deck Only)	1 Connect a camcorder or DV equipment to the DV IN connector
		on the unit’s front panel.
		2 Press HDD.
You can dub programmes from a camcorder or DV equipment
		3 Press PR +/– to set the channel to “DV”.
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV		● The on-screen display for DV dubbing appears.
equipment functions during dubbing.		4 Press w e to select		, then press ENTER to display
		the remote icon (facing to the right) for the DV equipment.
NOTES:		5 Press w e to select		FR360	00:00:00. 00		00:00:00. 00	L – R
● Use the DV cable VC-VDV 204U for connection.			, then press ENTER
					0:00	1:00	2:00	DV
					HDD		GR-DV3500
● When you connect a PC to the DV IN connector, we do not assure				12bit	DVJVC	GR-DV3500		SOUND1
		repeatedly until the desired sound
	the normal operation of this unit.
		track appears on the TV screen.

Your unit

DV IN connector

AUDIO 1: Select this to record the
original stereo sound played
back on the connected DV	DV	DV	1	2
equipment.

AUDIO 2: Select this to record the

dubbed stereo sound played back on the connected DV equipment.

MIX: Select this to record the sound of both “AUDIO 1” and “AUDIO 2”.

●Note that this selection is not available when the source programme is recorded in 16BIT (48 kHz) mode.

6 Press REC MODE repeatedly to set the recording mode.

Camcorder

DV equipment

DV cable (VC-VDV 204U)

(not provided)

DV connector

7 Locate the point from where you want to start dubbing, then stop or pause playback by pressing the following buttons on the remote control: 4, 5, 3, 8, 9

●To play back in slow speed (1/10 of the normal speed), press 9 to pause playback, then press 3 or 5.

●To play back frame-by-frame, press 9 to pause playback, then press 9 repeatedly. Each press of 9 advances a frame.

●To change the playback direction, press 3 or 5.

8 Press w e to select , then press ENTER. The dubbing starts.

●Playback on the external DV equipment and recording on the unit should start simultaneously.

●To pause dubbing, press w e to select , then press ENTER. Both the unit and the external DV equipment pause dubbing. Pressing 9 on the unit also works the same way.

9 Press 8 on the remote control to stop dubbing.

●Both the unit and the external DV equipment stop dubbing.

NOTES:

●Dubbing copyright guarded programmes is not possible.

●Original DV informations such as the recording date and time are not recorded.

●The superimposed indication during the operation or dubbing is not recorded.

●If the dubbing is paused while the channel is set to “DV”, you cannot switch channels.

When you dub from DV equipment other than a camcorder

APerform step 1 to 3.

BLocate the point from where you want to start dubbing, then stop on the DV equipment.

● If you pause the DV equipment in this step, a few second’s still picture will be recorded at the beginning of the recorded programme.

C Set the input mode to “DV INPUT” on the DV equipment.

● If you select an input mode other than “DV INPUT”, unwanted pictures may be recorded at the beginning of the recorded programme.

D Perform step 8 to 9.

To skip unwanted part of the source picture

Press ENTER to stop both equipment, then press w e to select

.

Locate the point where you want to restart dubbing by pressing 4, 5, or 3, then press 8.

Press w e to select , then press ENTER to restart dubbing.

Page 60

Thursday, 3 June 2004 10:46