Hitachi DV-RX5000U manual Manually programming timer recordings

Manually programming timer recordings

4

Press [ENTER]

when you have fin-

You can enter up to 16 programs up to a month in advance.

ished programming the timer.

Each daily or weekly program is counted as one program.

TIMER

Remaining Recording Time

1:58 SP

RECORDING

1

3/26 TUE12:55 PM

Press [PROG/CHECK].

No

CHANNEL

DATE

ON

OFF

MODE CHECK

01

64 ABC

3/ 26 TUE

1:00 PM

2:00 PM

SP

Enable

Displayed if the

02

64 ABC

3/ 26 TUE

2:30 PM

3:00 PM

SP

Enable

TIMER

Remaining Recording Time

1:58 SP

New Timer Program

recording can fit

RECORDING

3/26 TUE 12:55 PM

in the remaining

No CHANNEL

DATE

ON

OFF

MODE CHECK

space on the

01

64 ABC

3/ 26 TUE

1:00 PM

2:00 PM

SP

Enable

A line that is

New Timer Program

disc.

ready for

programming

is highlighted.

≥Press [3, 4] to select “New Timer Program” and repeat

steps 2- 4 to program other recordings.

SELECT

CANCEL

Press ENTER or VCR Plus+ to

5 Press [PROG/CHECK] or [RETURN].

ENTER

RETURN

store new program

The timer recording list disappears and the message “TURN

2

Press [ENTER].

RECORDER OFF FOR TIMER RECORDING” is shown on

the television.

TIMER		Remaining Recording Time 1:58 SP
RECORDING
						3/26 TUE 12:55 PM
	CHANNEL	DATE	ON		OFF	MODE
	3	----------	--:-- --		--:-- --	--
	4
	----
						Enter Title
		Please set Channel.
SELECT				No.
			0	--	9
ENTER	RETURN

3 Press [1] to move through the items

and change the items with [3, 4].

≥The current settings are shown each time you press [1].

≥You may use the numbered buttons to enter the CHANNEL, DATE, ON (start Time), and OFF (Finish Time).

TIMER
RECORDING	Remaining Recording Time	1:58 SP
	3/26 TUE 12:55 PM

CHANNEL DATE ON OFF MODE

64 ABC 3/ 26 TUE 2:30 PM 3:00 PM SP

Enter Title

≥CHANNEL (Channel number and caption)

≥DATE Current date

;

Next day up to one month later minus one day

;

Weekly timer: SUN-SAT>MON-SAT>MON-FRI

;

Daily timer: WEEKLY SUN>--->WEEKLY SAT

;

(Return to Current date)

≥ON (Start time)/OFF (Finish time)

The time increases or decreases in 30-minute increments if you hold the button.

≥MODE (Recording mode ➜page 15)

SP>XP>FR>EP>LP (>Return to SP)

≥Enter Title

Select “Enter Title” using [2, 1] and press [ENTER] (➜page 27).

6 Press [Í, DVD POWER].

Ensure “F” lights on the unit’s display.

To release the unit from recording standby

If you want to record something else before the program start time, for example:

Press [Í, DVD POWER].

The unit turns on and “F” goes out.

≥Be sure to press [Í, DVD POWER] to return the unit to

standby mode before the scheduled recording time. Timer recording will work only if “F” is displayed.

To stop recording when recording has already begun

Press [∫], then [ENTER] within 5 seconds.

Recording stops.

[Note]

≥The actual time recorded may be longer than the program itself when television programs are recorded using VCR Plusi.

≥If you don’t select a recording mode when using VCR Plus+ codes to make a timer recording, the unit sets the mode selected on the unit at that time (unless the mode is “XP”, in which case the unit sets “FR” as the mode).

≥“All timer programs are occupied.” appears if there are already 16 programs.

≥The remaining time displayed is based on the current record- ing mode.

≥When you program successive timer recordings to start immediately one after the other, the unit cannot record the part at the beginning of the later programs (a few seconds when recording with DVD-RAM and approximately 30 sec- onds when recording with DVD-R).

≥If you set DST (Daylight Saving Time) to ON when manually setting the clock (➜page 49), timer recording may not work when summer switches to winter and vice versa.

≥“F” flashes when the unit couldn’t go to timer recording standby (e.g., a disc isn’t loaded, a disc that can’t be recorded to is loaded, or the disc is protected). Check the disc carefully.

Timer recording

25