Tascam RC-601mkII owner manual Basic Operations, Preparations, Selecting the Playback Mode

Page 8

BASIC OPERATIONS

Online Playback and Monitor Playback

The CD-601MKII has two playback modes, online playback and monitor playback. The output destination in each of these playback modes can be set individually.

For example, in sites such as broadcasts and events, the monitor playback mode can be used to cue tracks or playback points before the final take, and then the remote control unit can be set to online standby (READY), and online playback can be performed from that point at the time of the final take.

On this remote control unit, the UNBALANCED analog output terminal and SPDIF digital output terminal are positioned as terminals for monitor output, and the BALANCED analog output terminal and AES/EBU digital output terminal are positioned as terminals for online output.

Note, however, that in the default setting both the monitor playback signal and the online playback signal are output in the same way from all analog/digital output terminals.

B y c h a n g i n g t h e m e n u s e t u p , y o u c a n s e t t h e UNBALANCED analog output terminal and SPDIF digital output terminal for monitor exclusive output, or the BALANCED analog output terminal and the AES/EBU digital output terminal for online exclusive output.

(→ page 24 “Setting the Terminals for Online Output”) (→ page 24 “Setting the Terminals for Monitor Output”)

[NOTE]

•This manual refers to the online playback standby state as “online READY” and the monitor playback standby state as “monitor PAUSE.”

Preparations

1Connect the RC-601MKII and CD-601MKII.

Use the remote cable provided with the remote control unit to connect the PLAYER UNIT terminal on the remote control unit with the REMOTE (SERIAL) terminal on the CD-601MKII.

CAUTION

•Perform the above connection with the CD-601MKII turned OFF.

Also turn the power OFF before disconnecting.

2Set whether to enable or disable operation on the CD-601MKII.

Select “R_L” or “R” at menu item No. 17 (“RMT”).

R_L: Operation is possible from both the RC-601MKII and CD-601MKII.

R: Operation is possible from only RC-601MKII. Operation of the CD-601MKII by other than the OPEN/CLOSE key and DISP MODE key is disabled.

z For details on menu operations, see “Menu Operations” (page 13).

3Turn the POWER switch on the rear panel of the CD-601MKII ON.

4Load a disc in the CD-601MKII.

z For details on loading discs, refer to “Preparations” in the CD-601MKII Owner’s Manual.

Selecting the Playback Mode

You can select the playback mode by using the PLAY MODE key.

Each press of this key switches the playback mode in the following order:

Regular playback (all tunes) → single playback → program playback

The current playback mode is displayed in the playback mode display area of the display window.

Playback Mode

Display Window

Operation

Regular playback

(nothing displayed) Tunes are played

 

 

back in disc track

 

 

o r d e r . ( r e g u l a r

 

 

playback)

Single playback

SINGLE lit

Only the selected

 

 

track is played back.

Program playback

PROGRAM lit

Tunes are played

 

 

back in the preset

 

 

program order.

zThe selected playback mode is backed up on the remote control unit. So, the same mode is reproduced when the remote control unit is next turned ON.

Playing a Specific Tune from the Beginning (SINGLE play)

The following describes the procedure for playing the final take (online playback) after selecting and confirming a desired tune (monitor playback). The following description assumes that the procedure is performed with menu items at their default settings.

1Select the single mode using the PLAY MODE key.

Press the PLAY MODE key several times until “SINGLE” lights in the playback mode display area of the display window.

2Press the PAUSE key to enter the monitor PAUSE mode. The PAUSE indicator starts blinking.

3Select the tune (track) to play back using the TRACK key.

The monitor PAUSE mode is enabled at the start of the selected track.

z The track can also be selected by using numeric keys. In this case, enter a 2-digit number. (e.g. In the case of track 2, enter “0” and then “2”.)

8 TASCAM RC-601MKII

Page 7 Page 9
Image 8
Page 7 Page 9
Contents RC-601MKII Contents Product Configuration CD-601MKII Operation SettingsAbout Backup Memory IntroductionNames & Functions of Parts Top Panel Play Mode key  Check key Memo key  A, B keysRear Panel Display Window Selecting the Playback Mode Basic OperationsPreparations Playing a Specific Tune from the Beginning Single playDisplay of playback position Playing from an Intermediate Point in a TuneAuto-registering Cue Points Details of Transport Key Operations Selecting the Playback Point Selecting a TrackTrack skip Specifying the track NoSelecting the Index Searching for an intermediate point in a tuneMenu Configuration Menu OperationsMenu Operation Basics Saving Menu Settings Clearing Menu SettingsClearing all user banks Clearing individual user banksPLAYBACK-RELATED Functions Program PlaybackSetting the Auto Cue Level Setting Auto Cue UpAuto Cue Function Auto Ready FunctionWhen the Monitor key is pressed during monitor playback Playback Mode Repeat OperationIncremental Play Function Repeat FunctionFunctions Using Memo A, B Points Setting Memo PointsClearing Memo Point Settings Locating Memo PointsConfirming the Audio of Memo Points rehearsal Playing Back from Point aPlaying Back up to Point B Playing between Points a and BDirectly Locating Cue Points Setting Cue PointsLocating Cue Points Clearing Cue Point Settings Functions Using CUE Points CUE1 to CUE10Confirming the Time of Cue Points Flash StartSaving Disc Information Memory BanksSaving Disc Information Reading Disc InformationOUTPUT-RELATED Settings Setting the Terminals for Online OutputSetting the Terminals for Monitor Output Setting Stereo/MonauralOther Functions & Settings Headphone Monitor FunctionsReferencing to an External Clock Source Failsafe FunctionChecking the Ending of Tracks Switching the Time DisplayDisplaying the End of Track Warning Timer Play Function External Control-related SettingsClearing the Frame Display Viewing the Total Motor TimeSpecifications List of Error MessagesHeadphone output electrical characteristics GeneralRC-601MKII

RC-601mkII specifications

The Tascam RC-601mkII is a versatile remote control designed specifically for use with Tascam's range of digital recorders and mixing consoles. This device is a valuable tool for audio professionals, allowing for seamless operation and enhanced workflow during recording and live sessions.

One of the standout features of the RC-601mkII is its comprehensive transport control, enabling users to play, stop, rewind, and fast forward with ease. The remote is equipped with large, clearly labeled buttons that provide tactile feedback, making it simple to operate even in high-pressure environments. The ability to control multiple devices with a single unit streamlines the recording process, minimizing the need to physically interact with the main equipment.

Incorporating advanced networking technology, the RC-601mkII allows for integration with various Tascam products via the RS-232C port and through MIDI protocol. This flexibility is especially beneficial in multi-device setups, where synchronized operation is crucial. Users can also take advantage of the remote's assignable buttons, which can be configured to trigger different functions on compatible devices, expanding its usability in live scenarios or studio setups.

Another significant characteristic of the RC-601mkII is its ergonomic design. The remote features a sturdy build that ensures durability, while its compact form allows for easy transport. This portability is ideal for musicians, sound engineers, and production teams who require reliable equipment that can withstand the rigors of various environments.

The display on the RC-601mkII is intuitive, providing clear information at a glance. Users can quickly access important functions and metrics, facilitating a smoother workflow. Additionally, the remote is powered via standard batteries or through an AC adapter, offering flexibility depending on user preferences and settings.

In summary, the Tascam RC-601mkII is a powerful remote control that enhances the functionality of Tascam's digital audio products. With its user-friendly transport controls, advanced connectivity options, and robust design, it serves as an indispensable tool for those in the audio industry, whether in the studio or on stage. The RC-601mkII exemplifies Tascam's commitment to quality and innovation, making it an excellent choice for anyone seeking to elevate their audio production experience.
Top Page Image Contents