Klipsch CS-700 owner manual Set-Top Box Connection, Cable Signal, T P U T S, Klipsch Controller

Page 6

STEP 3A: Set-Top Box Connection

Use this connection if your TV has a cable box, satellite receiver or HD receiver set-top box connected to it. See next page (3B) if no set-top box is used.

 

 

 

 

 

 

 

 

 

 

 

 

CABLE SIGNAL

CABLE BOX (shown)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

O U T P U T S

CABLE IN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COMPONENT

 

 

AUDIO

DIGITAL

 

HDMI OUT Y PB PR

VIDEO S-VIDEO L R

COAXIAL OPTICAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2A OR

- OR -

 

 

- OR -

 

2B

 

 

 

3A

2C

3B

3C

3D

 

 

 

 

 

- OR -

KLIPSCH CONTROLLER

1.Disconnect the cable on your cable, satellite or HD set-top box that is connected to your TV (you need to connect 1 video and 1 audio).

2.Connect the VIDEO—look at the options available on the set-top box and choose 2A, 2B or 2C.

A.B. To maintain best picture quality—if the back of the set-top box has HDMI or CoMPONENT Video (Y, PB, PR) OUTPUT jacks, plug corresponding cable(s) into the jack(s) on the set-top box and to the Klipsch system’s SAT/CABLE/HD INPUT HDMI or COMPONENT jacks (Y to Y; PB to PB, PR to PR). If you use 2A or 2B, you must also connect the corresponding output from the Klipsch controller’s “ViDEO Output” section to your TV to ensure that you get a picture. These cables have not been included with the Klipsch system. When using the HDMI connections you must turn Progressive Scan (P. Scan) “On”. If the HDMI connections are used and P. Scan is “Off”, you will not see a picture.

C.If the set-top box has a ViDEO (yellow) OUTPUT jack for video, plug the supplied yellow video cable into that jack and to the Klipsch system’s SAT/CABLE/HD INPUT COMPOSITE (yellow) jack.

3.Connect the AUDIO—look at the options available on the set-top box and choose 3A, 3B, 3C or 3D.

A.If an HDMI cable is used, audio is already connected through this cable.

B.Connect the supplied audio cables to the AuDIO Left (white) and AuDIO Right (red) jacks on the back of the set-top box and to the Klipsch system’s SAT/CABLE/HD INPUT Left (white) and Right (red) jacks.

C.If the set-top box has Digital AuDIO (COAXIAL), connect appropri- ate cable to the set-top box AuDIO Coaxial jack and to the SAT/CABLE/HD INPUT coaxial jack.

D.If the set-top box has Digital AuDIO (OPTICAL), connect appropriate cable (not supplied) to the Klipsch System’s SAT/CABLE/HD INPUT OPTICAL jack. You will first need to remove the plastic dust plug.

Note: If you connect a high definition Y, PB, PR input, you must also connect the corresponding Y, PB, PR output to your TV. If you connect a HDMI, you must also connect the corresponding output from the Klipsch controller’s “ViDeo Output” section to your TV to ensure that you get a picture. These cables have not been included with the Klipsch system.

Input and Output Jacks

Please see appendix I (page 28) for the basics on how input and output jacks work with your Klipsch system.

Image 6
Contents CS-700 Table of Contents Important Safety Information DVD Safety InformationDVD Copy Protection Reading this Manual Connecting your systemThank You Step-by-Step ConnectionsPut the batteries in the remote control Unpack the boxT P U T S Cable SignalSet-Top Box Connection Klipsch ControllerTV Audio Connection TV Back PanelOFF-AIR Connect Klipsch System to the TVs Input TV Back PanelProperly On the left when you are facing the systemConnect the Speakers Subwoofer onConnecting a component to AUX 2 Input side Connecting headphones to HeaDPhone OutputConnecting a component to AUX 1 Input Connecting a device with USB to USB connectorAM Antenna Connect AM and FM Antennas suppliedFM Antenna Turn on the TV and the Klipsch SystemComplete the On-screen Setup By other Klipsch audio products using KlipschCast technology Your Klipsch Controller Switching between media-TV, DVD, Radio, CDs, etc BasicsRemote control Programming Your Remote Control Incompatible Discs OperationCompatible Discs Regional CodingDVD and VCD Playback Features TransportNavigating Info Banners SubtitlePlaying CDs Or the Ç arrow buttonOn-screen info banner Setting up presetsPlaying CDs with mp3 or Jpeg files Playing the RadioOn-Screen Menu System To access the menu system, press Menu the main menu appearsMenu System Navigating MenusSetup On-Screen Menus AudioLanguages Parental Control Troubleshooting Klipsch System Care and MaintenanceCleaning Handling and Caring for DiscsRemote Control Code Lists Remote Control Code Lists FCC Declaration Of Conformity Trade Name Video Grade Cables Appendix I Connection OverviewMatches Not suppliedPower Detail