JVC HR-XVC33UM manual Connection, 14 EN, DVD deck only, Set the VCR channel to off

Page 14

Filename [XVC33UM_06Index.fm]
XVC33UM_06Index.fm Page 14 Tuesday, September 9, 2003 9:27 AM	Masterpage:Left+

14 EN

INSTALLING YOUR NEW UNIT (cont.)

S-VIDEO

Connection

(DVD deck only)

ATTENTION

Be sure to connect the unit’s VIDEO OUTPUT (DVD/ VCR) connector to the TV’s VIDEO input connector.

Antenna or Cable
	Coaxial cable
	Flat feeder
		Matching transformer
		(not supplied)
AC outlet	S VIDEO OUTPUT		AUDIO OUTPUT
			AUDIO OUTPUT
AC power cord			VIDEO OUTPUT

PCM/STREAM

OPTICAL COAXIAL

Back of unit		VHF/UHF
		VHF/UHF
		IN
S-Video cable	Audio/video	VHF/UHF
(not supplied)	cable	VHF/UHF
	(not supplied)	OUT
		RF cable
		(supplied)

To S-VIDEO input	To 75 ohm
connector	Terminal
	TV

8To connect to a TV with S-VIDEO/AUDIO input connectors . . .

A Connect the unit to TV.

AConnect the antenna, unit and TV as per “AV Connection”. ( pg. 13)

BConnect the unit’s S VIDEO OUTPUT (DVD) connector to the TV’s S-VIDEO input connector.

B Connect the unit to power source.

Plug the end of the AC power cord into an AC outlet.

C Set the VCR channel to off.

Before performing the following steps:

●Make sure there is no cassette inserted in the unit.

●Make sure the unit is turned on, then press VCR/ DVD on the unit or VCR on the Remote so that the VCR indicator lights up.

AWhen the unit is turned off, press STOP (8) on the unit for more than 5 seconds. “3 CH” appears on the front display panel.

BPress CH +/– on the Remote to select “– CH” (off),

then press OK.

●If Plug&Play or Tuner setting has not previously been performed, the Language Select screen appears and Plug&Play takes place automatically.

NOTES:

●You can obtain high-quality S-VHS pictures when you play back discs on the DVD deck.

●If your TV is not stereo-capable, use the unit’s AUDIO OUTPUT connectors to connect to an audio amplifier for Hi-Fi stereo sound reproduction.

●To operate the unit with your TV using the S-VIDEO connection, set your TV to its AV mode. You can also use the

TV/VCR button on the unit’s Remote to set your TV to the AV mode. ( pg. 73)

●For switching the TV’s mode, refer to the instruction manual of your television.

Page 14

9 September 2003 9:26 am

Image 14

Contents HR-XVC33UM Dear Customer Filename XVC33UM03Safety.fmUse only discs marked with the following Audio CDs Cm /12 cm discTo mobile phone users Do not place the unitDo not block the unit’s ventilation openings or holes On placing the unitAbout Discs Dubbing from DVD to VCR Remote Control FunctionsEdit From a Camcorder Basic ConnectionsUnplayable Discs About DiscsPlayable Discs Region NumberMarks related to video DVD Video MarksFile Structure of Discs Audio CD/Video CDOpen the disc tray Placing a DiscCare and Handling of Discs Place the discFront View Filename XVC33UM06Index.fmRear View August 2003 500 pmCassette Type Indicator VCR deck only 10 ENOn the tape ON-SCREEN Display VCR deckTo recall an indication How To Use 12 ENConnect the unit to TV Connect the unit to power sourceCheck the contents Situate the unit14 EN 8To connect to a TV with S-VIDEO/AUDIO input connectorsConnection DVD deck onlyComponent Audio/Video 8To connect to a TV with component video input connectorsInput connector Terminal Video cable CableAuto Channel Set Plug & Play Set16 EN Press Menu Monitor Set DVD deckPan&Scan Default setting is bold in the table belowPan&Scan/Letter Box Letter BoxLanguage Access the Main Menu screenAccess the Initial Set screen 20 ENPress w e to select Language On-screen Language Set DVD deckPress rtto move 0 to on Screen LANGUAGE, then press OK Press rt to move 0 to Menu LANGUAGE, then press OK See Language Code List pg22 EN Language Code List 24 EN Access the Clock Set screenClock Set To make corrections any time during the process Press SET UP Menu and normal screen appearsStart clock 26 EN Access the Tuner Set screenTuner Set Perform Auto Channel SetAdd or skip the desired channels Access the Manual Channel Set screenManual Channel Set To add channelsStart playback Basic PlaybackFind the program start point Stop playbackPause during playback Slow MotionHigh-Speed Turbo Search Activate frame-by-frame playbackInstant ReView 30 ENIndex Search Skip Search Activate Index SearchActivate Repeat Playback Next Function MemoryRepeat Playback Stop Repeat PlaybackManual Tracking Adjust the tracking manually32 EN Soundtrack SelectionSet the tape speed Load a cassetteChoose a program Start recording34 EN Instant Timer Recording ITREngage the ITR mode Accidental erasure preventionTape Remaining Time Reset the counterElapsed Recording Time Indication Second Audio RecordingEnter the program start time Access the Program screen36 EN Enter the program stop timeEnter the channel position Engage the unit’s timer modeTo Timer-Record Weekly Or Daily Serials Cable Box or DBS Receiver UsersAccess the Program Check screen Check, cancel and change programsDisengage the timer mode 38 ENReturn to the timer mode To cancel or change a programCancel or change a program Press Timer40 EN When programs overlap each otherCancel or change program setting Confirm the overlapping programsRecording Engage the Satellite Auto Recording modeSatellite Auto Pause playback 42 ENLoad the disc Press OPEN/CLOSE x on the DVD deck to open Disc trayAccess the DVD menu Locating a desired scene using the DVD menuAccess the PBC menu Stop modeHigh-Speed Search 44 ENLocating the start point of the item or skip the item Press Skip 2 or Skip 6 during playbackZooming Still Picture/Frame-By-FramePlayback Resume Function3D Phonic Access the selection menu46 EN Select the effect levelAdjusting the picture quality VFP functionScreen bar Using the onContents of the on-screen bar during playback 48 ENSelect menu item Access the on-screen barChange the time information Select the option50 EN Select the repeat modeAccess the repeat mode Select the start point Select the chapter 52 ENChapter Search ExamplesSelect the menu item To clear the program table Press Play SetupProgram Playback Random Playback Select the tracks in the desired orderSubtitle Selection Access the menu54 EN Select the subtitle languageAngle Selection Select the view angle Access the menuWhen using the Angle button Select the view angleAudio Language Selection When using the A.MONITOR button56 EN Select the audio languageFor Video CD Audio Channel SelectionSelect the audio channel For SvcdAccess the DVD Set Up menu Access the Parental Lock menuAccess the country code menu Parental LockTo change the settings To temporarily release the Parental LockCountry/Area Code List for Parental Lock 60 ENXVC33UM01.book Page 61 Monday, August 4, 2003 724 PM MP3 control display What is MP3?62 EN Select the group Using the MP3 control displayMP3 Playback To return to the MP3 control display 64 ENGroup/track selection To start playback by specifying the group/track numberCD-RW disc What is JPEG?Jpeg control display Press rt to select the desired file, then press OK or Play 66 ENBe sure to set MP3/JPEG to Jpeg before loading a disc. pg Slide-show playback starts from the selected fileTo return to the Jpeg control display Press Play Setup while the Jpeg Control screen is displayedGroup/file selection Press Zoom during playbackEdit From a Camcorder 68 ENAnother Video Recorder Set the input mode of recording deckEngage the Record Pause mode of the recording deck Start the source playerFrom DVD to VCR Dubbing70 EN Prepare the audio device for dubbing Digital Audio DubbingPlace a disc and load a MD For the digital audio deviceFunctions 72 ENSet the TV brand code TV Multi-Brand Remote ControlTV/VCR CH +/- , TV VOL+/- Volume, Mute TV Muting, number keysBack of unit 74 ENMake connections For each mode setting, see pages 76 to Mode SetAccess the Function Set screen VCR deck76 EN For ExampleWhen this function is set to on 78 EN Language Picture Audio Others Back to the beginningPicture Settings Audio Settings80 EN Others Settings Child Lock Scan Mode SetSwitch the mode 82 ENOn the unit On the Remote84 EN DVD indicator lights upPress DVD so that the DVD indicator Lights upTheir file names Cover the hole where the tab wasSuch as .Mp3 to their file names Jpeg files are not recorded in a format86 EN Display panel VCR indicator disappears from the frontDistorted on the TV screen Deck is selected Resume recordingPlayback Timer Recording 88 ENPrograms Memory backup time Approx minutes Tuning system Frequency synthesized tuner Channel coverageTo Channel 3 when shipped Signal-to-noise ratio 45 dB90 EN Manual Channel Set Manual Tracking Mode Set DVD deckMode Set VCR deck Repeat Playback About DiscsPlug&Play Set Program Playback Random Playback Zooming 3D PhonicFilename XVC33UM13Cov4.fm May 10, 2004 645 pm