LG Electronics 37LC50DC manual Detailed Descriptions of Installer Menu Items, Installer Sequence

Page 12

Installer Menu

Detailed Descriptions of Installer Menu Items

000 - INSTALLER SEQUENCE

Specifies entry sequence to the Installer Menu.

0 = 9876

1 = 4321

2 = 1478

3 = 3698

001 - POWER MANAGE (Power Management)

Determines hours of no activity before automatic shutoff. The POWER MANAGE function is for saving energy. If set to 0, Power Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain On, unless there has been activity from either the control panel or remote control.

002 - AC ON (AC Power Switchable)

If set to 1, allows the TV to turn On just by applying AC power. Pressing the On button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use ADJ Left/Right arrow to choose 0 or 1 where 0 is the default is Off, and 1 is On.

NOTE: If set to 1 (On), the TV does not respond to On/Off commands from either the remote or the display control panel, and the SLEEP TIMER is also nonfunctional.

003 - BAND/AFC (Band/Automatic Frequency Control) There are 4 possible settings for this option:

0

= Broadcast

1

= CATV

2

= HRC

3

= IRC

If some channels were not found by EZ SCAN (Auto Program), select the appropriate Band setting here and add the channels using the Channel Edit option in the Setup Menu.

004 - STRT CHANNEL (Start Channel)

If active, this function allows you to determine the initial channel number when the TV is turned On. This feature is useful for an in- house information channel, since the TV would always select that channel when it is turned On. Setting this to 255 causes the last channel viewed when the TV was turned Off, to be the tuned to chan- nel when the TV is turned On again. Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number.

255

= Last channel

1 ~ 125 = Ch X

0 = Aux

126

Map to Channel 3.

127 Map to Channel 4.

005 - CHAN LOCK (Channel Lock)

CHAN LOCK is ideal if the system must always be on the same channel. Changing channels with Channel Up/Down or keypad numbers is impos- sible. Channel Lock is inactive if set to 0 (default).

Generally, this feature is used in connection with START CHANNEL (Installer item 004) where the start channel may, for example, be set to 3 or 4. If the start channel is 3, then the TV will remain locked on Channel 3.

NOTE: For Items 007, 008 and 009

For legacy reasons, the scale used is 0 - 63. The PTC software will translate this to the 0 - 100 scale used by the TV.

To translate a TV volume level to the installer menu value, use the fol- lowing formula:

Installer Value = TV Value x 63 100

Enter only the whole number (disregard fractions).

007 - STRT VOLUME (Start Volume)

This function allows the Installer to determine the initial volume level setting when the TV is turned On. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned On. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned Off; at turn On, the volume level will be automatically set at the previous or last level.

008 - MIN VOLUME (Minimum Volume)

This function determines the minimum volume level allowable with the VOLUME (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63

change values with ADJ Left/Right arrow. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOL- UME is also set to 63. It may be best to set the same value on every TV.

NOTE: The minimum volume level cannot have a value setting higher than the MAX VOLUME level (described below).

009 - MAX VOLUME (Maximum Volume)

This function determines the maximum volume level allowable with the VOLUME (VOL) Up/Down controls. In this way, for example, someone can not set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0. Change values with ADJ Left/Right arrow keys. It may be best to set the same value on every TV.

NOTE: The maximum volume level cannot have a value setting lower than the MIN VOLUME level (described previously).

010 - MUTE DISABLE

Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted.

P A G E 1 2

206-4071

Image 12
Contents Integrated TVs Typical Installer Menu Table of Contents Typical Installer Multi-Brand Remote Control Installing Batteries in Installer Remote ControlInstaller Remote Control Typical Key Functions MultiCommercial Mode Setup for Master TV Cloning Connections/Learning Setup Turn to the next page to continue Cloning SetupBefore you begin cloning Master TV Clone ProgrammerCloning Learning Setup Learning the Master TV Setup Learn Setup from Master TVLT2002 Clone Programmer Communication Problems Set the Clock OptionalTeach Master TV’s Setup to the target TV Disconnect TV Power for 15 SecondsTarget TV Clone Programmer Installer Menu Accessing the Installer’s MenuUsing the Installer’s Menu Installer Menu Items 000 throughInstaller Menu Items 035 through Detailed Descriptions of Installer Menu Items Installer SequenceMute Disable Sleep Timer Caption LockPoll Rate Timing PulseAUX Status Atsc Tune Mode Back LightingAtsc Band Start Minor ChannelReference Clonable Menu Features Clonable Menu FeaturesAdding Channel Icons and Labels in the 2-5-4 + Menu Mode Reference Detailed Information For Making a Master TV Making a Master TVDetailed Instructions Procedure for Checking Software Version Reference Checking Software VersionTV Camport Auto Sense Operation Camport Operation Stand-AloneCamport Operation PPV TV Aux Input Configuration / Troubleshooting TroubleshootingTroubleshooting Reference Cloning Procedure Troubleshooting Reset Clone After Static ShockClone Programmer Troubleshooting Problem Possible Causes Possible Solutions Clone ProgrammerTroubleshooting Flow Chart Controller Quick CheckCommercial Mode Check Reference RJP Mode Configuration Glossary of Terms Copyright 2008, LG Electronics U.S.A., Inc