LG Electronics 37LC50DC, 206-4071P manual Troubleshooting

Page 22

Troubleshooting

Some quick and easy tips to resolving problems

SymptomsPossible Cause(s)Possible Solution(s)See Page(s)

Power

No Power.See troubleshooting flow chart.24

Display Panel Picture

No Picture.

• Display panel is turned off.

-Turn TV on.

 

 

 

-Power failure?

 

 

• Antenna/Cable not connected.

-Connect Antenna/Cable signal to TV.

(See Owners manual)

 

• Connections incorrect.

-Check connections on TV.

(See Owners manual)

 

• M.P.I. not connected.

-If applicable, connect M.P.I. cable to M.P.I. device.

 

 

• Encrypted program.

-Try another channel.

 

 

• Wrong tuning band.

-Adjust Installer menu settings.

10 ~ 15

 

 

 

 

Erratic Operation

Installer menu setup. • Wrong Installer menu settings. -Adjust Installer menu settings as required.10 ~ 15

Remote Control

Remote doesn’t work.

• Remote not in TV mode.

-Use Mode key to select TV; puts remote into TV mode.

5

 

• Not aimed at IR remote sensor.

-Point remote at TV’s IR receiver on TV.

 

 

• Remote too far from IR sensor.

-Move remote closer to TV’s IR receiver or darken room.

 

 

• IR path to TV’s receiver obstructed.

-Remove obstructions.

 

 

• Weak batteries.

-Replace batteries.

4

 

• Wrong battery polarity.

-Check that “+” and “-” match in battery compartment.

5

 

• Too much light in room.

-Dim room light.

 

 

• Wrong Installer remote control.

-Requires compatible Installer remote, contact your LG dealer.

2

 

 

 

 

Picture Reception

Normal picture, poor

• Audio muted.

-Press MUTE or use Volume Up key to increase sound level.

5

or no sound.

• Broadcast problem.

-Try a different channel.

5

 

 

 

 

Note: For other problems not caused by the TV, refer to other devices’ operating guide.

P A G E 2 2

206-4071

Image 22
Contents Integrated TVs Typical Installer Menu Table of Contents Typical Installer Multi-Brand Remote Control Installing Batteries in Installer Remote ControlInstaller Remote Control Typical Key Functions MultiCommercial Mode Setup for Master TV Before you begin cloning Cloning Connections/Learning SetupTurn to the next page to continue Cloning Setup Master TV Clone ProgrammerLT2002 Clone Programmer Communication Problems Cloning Learning Setup Learning the Master TV SetupLearn Setup from Master TV Set the Clock OptionalDisconnect TV Power for 15 Seconds Teach Master TV’s Setup to the target TVTarget TV Clone Programmer Using the Installer’s Menu Installer MenuAccessing the Installer’s Menu Installer Menu Items 000 throughInstaller Menu Items 035 through Installer Sequence Detailed Descriptions of Installer Menu ItemsMute Disable Poll Rate Sleep TimerCaption Lock Timing PulseAUX Status Atsc Band Atsc Tune ModeBack Lighting Start Minor ChannelReference Clonable Menu Features Clonable Menu FeaturesAdding Channel Icons and Labels in the 2-5-4 + Menu Mode Making a Master TV Reference Detailed Information For Making a Master TVDetailed Instructions Procedure for Checking Software Version Reference Checking Software VersionCamport Operation Stand-Alone TV Camport Auto Sense OperationCamport Operation PPV TV Aux Input Configuration / Troubleshooting TroubleshootingTroubleshooting Clone Programmer Troubleshooting Reference Cloning Procedure TroubleshootingReset Clone After Static Shock Problem Possible Causes Possible Solutions Clone ProgrammerTroubleshooting Flow Chart Controller Quick CheckCommercial Mode Check Reference RJP Mode Configuration Glossary of Terms Copyright 2008, LG Electronics U.S.A., Inc