LG Electronics 37LC50DC, 206-4071P manual Cloning Learning Setup Learning the Master TV Setup

Page 8

Cloning Learning Setup

Learning the Master TV Setup

Instructions for the Clone Programmer to Learn the Master TV Setup

Use MPI Cable to Connect LT2002 Clone Programmer to Master TV MPI Port

If there is a good connection, “THE CLONE HAS CONTROL OF TV” message will appear. Press any key on the Installer remote.

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

XX

THE TV IS VERSION

XX

THE SW IS REVISION

XX

CLONE CLOCK=

XX:XX

TV

CLOCK=

XX:XX

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

Learn Setup from Master TV

Press 1 to select the “LEARN FROM TV” option, then press ON/OFF, POWER, or ENTER to go to the Memory Bank Selection Menu. Pick the Memory ”Bank” you want to store the master TV’s setup in by press- ing either Channel key repeatedly to choose Memory 1, 2 or 3. (If you choose a Memory “Bank” that has a master device’s setup pro- grammed into it, that setup will be overwritten by the new master TV’s setup.) Once the Clone memory bank is selected, press ON/OFF, POWER, or ENTER. The Clone memory bank you have selected will be shown. Press ON/OFF or POWER to begin copying the master TV’s setup.

This menu should appear by itself after the LT2002 is connected to the TV MPI port.

CLONE SELECTION MENU

(1)LEARN FROM TV

(2)TEACH TO TV

(3)SET CLONE CLOCK FROM TV

(4)SET TV CLOCK FROM CLONE

(5)DISPLAY TV SETUP

(6)DISPLAY CLONE SETUP

Set the Clock (Optional)

Set the time on a Master TV’s Clock. (If the time has already been copied from a TV into the Clone programmer, you can set a master TV’s clock by copying the time from the Clone programmer.) The Clone Programmer can copy the current time to both a master TV and to the Clone’s internal clock; accurate to within one minute. (Another reason that the Clone programmer should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurate- ly as possible.)

Since the Clone Programmer’s time cannot be set directly, the current time needs to be copied from a Zenith/LG TV equipped with M.P.I. input capability.

After the time is copied to the Clone programmer, the current time can then be transferred to another TV. (This can be a master TV, or another TV which has already had the features set up.)

-TO CHANGE MENU ITEMS, PRESS CHANNEL KEYS OR DIGITS.

-TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER

This menu should appear after any key is pressed on the Installer remote.

LT2002 Clone Programmer Communication Problems

A slow flashing green light indicates there are communica- tion problems between the TV and the LT2002 clone program- mer. If this is the case, check for a damaged cable, poor con- tacts, or other connection troubles.

If the status indicator is red, the programmer batteries are low and should be replaced. Install 4 high-quality alkaline AA batteries.

P A G E 8

206-4071

Image 8
Contents Integrated TVs Typical Installer Menu Table of Contents Typical Installer Multi-Brand Remote Control Installing Batteries in Installer Remote ControlInstaller Remote Control Typical Key Functions MultiCommercial Mode Setup for Master TV Cloning Connections/Learning Setup Turn to the next page to continue Cloning SetupBefore you begin cloning Master TV Clone ProgrammerCloning Learning Setup Learning the Master TV Setup Learn Setup from Master TVLT2002 Clone Programmer Communication Problems Set the Clock OptionalTarget TV Clone Programmer Teach Master TV’s Setup to the target TVDisconnect TV Power for 15 Seconds Installer Menu Accessing the Installer’s MenuUsing the Installer’s Menu Installer Menu Items 000 throughInstaller Menu Items 035 through Mute Disable Detailed Descriptions of Installer Menu ItemsInstaller Sequence Sleep Timer Caption LockPoll Rate Timing PulseAUX Status Atsc Tune Mode Back LightingAtsc Band Start Minor ChannelReference Clonable Menu Features Clonable Menu FeaturesAdding Channel Icons and Labels in the 2-5-4 + Menu Mode Detailed Instructions Reference Detailed Information For Making a Master TVMaking a Master TV Procedure for Checking Software Version Reference Checking Software VersionCamport Operation PPV TV Camport Auto Sense OperationCamport Operation Stand-Alone TV Aux Input Configuration / Troubleshooting TroubleshootingTroubleshooting Reference Cloning Procedure Troubleshooting Reset Clone After Static ShockClone Programmer Troubleshooting Problem Possible Causes Possible Solutions Clone ProgrammerTroubleshooting Flow Chart Controller Quick CheckCommercial Mode Check Reference RJP Mode Configuration Glossary of Terms Copyright 2008, LG Electronics U.S.A., Inc