LG Electronics 206-4071P, 37LC50DC Cloning Connections/Learning Setup, Before you begin cloning

Page 7

Cloning Connections/Learning Setup

Connections for the LT2002 Clone Programmer to Learn the TV Master TV Setup

Antenna

or CATV

Warning: Do not use LT2002 while any PPV card is installed in TV or clone programmer device

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION

XX

THE TV IS VERSION

XX

THE SW IS REVISION

XX

CLONE CLOCK

= XX:XX

 

TV CLOCK

= XX:XX

 

-PRESS ANY KEY TO CONTINUE.

-DISCONNECT CLONE WHEN DONE.

Ferrite Core (TDK, ZCAT

2035-0930)

Connect cable to

 

 

 

 

TV MPI Jack and

 

 

Status

follow on screen

 

 

instructions

 

Indicator

 

 

 

 

 

MPI

Reset

Color

• green

battery ok

• red

battery low

Blink pattern

• slow

power on

 

no communications

• heartbeat

power on

 

communications ok

®

 

QuickSet II Programmer

LT2002

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS USA

will be damaged.

Master TV

Clone Programmer

Notes: It is assumed that the TV is connected to a signal source, the source selected is Antenna (RF) In, the signal is from an Analog channel, not a digital channel, all equipment is connected to power and turned on and the LT2002 Clone Programmer main menu (THE CLONE HAS CONTROL OF THE TV) menu is displayed on the TV screen, see above and next page.

Before you begin cloning...

The Master TV should be connected to a good, stable signal from an over-the-air antenna or cable service Analog channel and connected to power. (See above.)

Teaching and Learning is only possible between identical model devices. (However, the LT2002 Clone programmer can store up to 3 different ‘master’ setups.)

WARNING: Copying a blank or incorrect memory into a TV, STB or other device will cause the TV, STB or other device to operate erratically or become inoperable.

Use an Installer’s remote to operate Learning and Teaching menus.

Make sure that the batteries in the Clone programmer are fresh.

If batteries are removed, the Clone Clock time will be lost.

Decide if you want to set the time from the Clone program- mer or copy the time to the Clone programmer; from a com- patible TV which has the clock set to the current time.

Setting the time and transferring it to the Clone or other device is a separate procedure.

Follow the connection diagram above to connect the Clone to a Master TV TV display panel. After learning is complete, to another identical TV TV display panel to “teach” it the master setup.

See the Clone Troubleshooting section to resolve problems.

Turn to the next page to continue Cloning Setup.

206-4071

P A G E 7

Image 7
Contents Integrated TVs Typical Installer Menu Table of Contents Installing Batteries in Installer Remote Control Typical Installer Multi-Brand Remote ControlMulti Installer Remote Control Typical Key FunctionsCommercial Mode Setup for Master TV Master TV Clone Programmer Cloning Connections/Learning SetupTurn to the next page to continue Cloning Setup Before you begin cloningSet the Clock Optional Cloning Learning Setup Learning the Master TV SetupLearn Setup from Master TV LT2002 Clone Programmer Communication ProblemsDisconnect TV Power for 15 Seconds Teach Master TV’s Setup to the target TVTarget TV Clone Programmer Installer Menu Items 000 through Installer MenuAccessing the Installer’s Menu Using the Installer’s MenuInstaller Menu Items 035 through Installer Sequence Detailed Descriptions of Installer Menu ItemsMute Disable Timing Pulse Sleep TimerCaption Lock Poll RateAUX Status Start Minor Channel Atsc Tune ModeBack Lighting Atsc BandClonable Menu Features Reference Clonable Menu FeaturesAdding Channel Icons and Labels in the 2-5-4 + Menu Mode Making a Master TV Reference Detailed Information For Making a Master TVDetailed Instructions Reference Checking Software Version Procedure for Checking Software VersionCamport Operation Stand-Alone TV Camport Auto Sense OperationCamport Operation PPV Troubleshooting TV Aux Input Configuration / TroubleshootingTroubleshooting Problem Possible Causes Possible Solutions Clone Programmer Reference Cloning Procedure TroubleshootingReset Clone After Static Shock Clone Programmer TroubleshootingController Quick Check Troubleshooting Flow ChartCommercial Mode Check Reference RJP Mode Configuration Glossary of Terms Copyright 2008, LG Electronics U.S.A., Inc