Peerless Industries SWS320/SI, SWS320/BK manual Installing Tilt Brackets

Page 7

Installing Tilt Brackets

WARNING

Tighten screws so adapter brackets are firmly attached. Do not tighten with excessive force. Overtightening can cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.

If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly secured, damage may occur to screen or product may fail.

To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place

2 screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (BB or CC) on back of screen, align to holes, and center on back of screen as shown below. Attach the adapter brackets to the back of the screen using the appropriate combination of screws, multi- washers, and spacers as shown in figure 2.1 or 2.2.

NOTE: Top and bottom mounting holes on screen must be used for attaching brackets.

NOTE: Be sure to attach tilt brackets with handles facing outward as shown below. Verify that all holes are properly aligned, and then tighten screws using a phillips screwdriver.

X

CC

CENTER BRACKETS

VERTICALLY ON BACK

OF SCREEN

X

NOTE: "X" dimensions should be equal.

HANDLES FACE OUT

BB

MULTI-WASHER

MEDIUM HOLE FOR M5 SCREWS

SMALL HOLE FOR M4 SCREWS

LARGE HOLE FOR M6 SCREWS

Notes:

The number of fasteners used will vary, depending upon the type of screen.

Multi-washers and spacers may not be used, depending upon the type of screen.

Use the corresponding hole in the multi- washer that matches your screw size as shown.

NOTE: For flat back screens proceed to step 2-1. For bump-out or recessed back screen skip to step 2-2.

7 of 38

ISSUED: 11-21-07 SHEET #: 202-9255-5 05-12-10

Image 7
Contents Features Table of Contents Tools Needed for AssemblyParts List Non-Security Tilt Bracket Fasteners Installation to Double Wood Stud Wall View Incorrect Correct Installation to Solid Concrete or Cinder BlockInstalling Tilt Brackets For Flat Back Screen Mounting and Removing Flat Panel Screen Adjusting the Tilt Angle of the Flat PanelScreen Características 11 de Herramientas necesarias para el ensamblajeContenido EspañolDe pieza ST650 ST650-S ST650P ST650P-S Descripción12 de 13 de Sujetadores no aseguradores para los soportes inclinables14 de Instalación en una pared con montantes de madera dobles15 de AA DDNotas Instalación de los soportes inclinables16 de 17 de Ajustar el ángulo de inclinación de la pantalla Instalación y desinstalación de la pantalla plana18 de Caractéristiques Français Outils nécessaires au montage20 sur 21 sur Liste des pièces22 sur Fixations du supports inclinables sans sécurité23 sur Installation sur un mur à doubles montants en boisVUE 24 sur25 sur Installation des support inclinables26 sur Pour les écrans à dos platRéglage de l’inclinaison de l’écran plat Installation de l’écran plat sur la plaque murale27 sur Merkmale Inhaltsverzeichnis Für den Zusammenbau erforderliche WerkzeugeDeutsch Teileliste Befestigungsteile für Sicherheitskipphalterung Abbildung Installation zu verdoppeln HolzständerreiheFalsch Richtig Installation zu massivbeton oder porenbetonsteinAnbringung von Kipphalterungen AchtungBildschirme mit flacher Rückseite 36 von Anbringung und Abnahme des FlachbildschirmsEinstellung des Neigungswinkels des FlachbildschirmsLimited FIVE-YEAR Warranty Garantie DE Cinq ANS