Sima Products SUR-35 Displaying Version Number, Turning the Touch Screen On, Version number

Page 10

Touch Screen

 

SUR-35 User Manual

 

 

 

Touch Screen

The touch screen reduces the number of buttons by changing its configuration for each device selected. In this way, the touch screen can provide a total of 768 buttons (16 devices x 2 pages x 24 buttons per page).

Turning the Touch Screen On

Using the touch screen is easy. Simply touch the screen or any hard button to activate it. The SUR-35 will turn itself off

automatically. (To change the programmable power down time, see Power Down Time Period in Chapter 7 – Changing SUR-35 Parameters.)

Figure 5: Touch the Screen To Turn It On

Touch Screen Precautions

Please read the following instructions carefully:

•Tap the LCD touch screen gently; never use force.

•Do not use a pen or any sharp object to tap the screen. You might damage the surface.

•Keep the touch screen dry. Wipe off any spills immediately. The SUR-35 is not waterproof; never immerse it in liquid.

•Don’t expose the SUR-35 to extreme temperatures. Keep it away from heat sources.

•Avoid dropping the SUR-35.

•Don’t drop anything on the touch screen.

•Clean the LCD touch screen with a soft cloth. If needed,

dampen the cloth slightly before cleaning. Never use Ch. abrasives or cleaning solutions.

2

Page

SUR-35 User Manual

 

Version number

Displaying Version Number

For technical support reasons, the Program and Data version numbers might be needed by Sima.

To display the version number, use the VER selection in the SETUP Menu.

1.Press and hold the SETUP button on the Touch Screen for 3 sec. Press each number button (2, 4, 6, 8) until it disappears.

2.Use the arrow buttons on the Touch Screen to select VER (displayed in the upper right corner) and then press the OK button.

Press the OK button again. Use arrow buttons to select PROG. The software version number appears under the PROG menu.

Use the arrows again to select DATA. The data version number appears under the DATA menu.

Press EXIT to exit.

Ch.

6

Page

10

51

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Warranty Day Limited WarrantyAbout this manual TroubleshootingPreface CopyrightTable of Contents Appendix C Troubleshooting Creating and Using MacrosAccessories Appendix B AccessoriesSUR-35 Features Introducing the SUR-35Unpacking the SUR-35 Appendix a SpecificationsSpecifications Identifying ComponentsGetting Started Features OverviewResetting to Factory Defaults Beep TogglingBacklight Time Period FeaturesFeatures BacklightPower Down Power Down Time PeriodInstalling Batteries Changing SUR-35 ParametersTouch Screen Touch ScreenDisplaying Version Number Turning the Touch Screen OnRubber Buttons Using Sleep ModeSleep mode Touch Screen ButtonsMenus Transmitting System SetupUsing Quick Channel Lists Program MenusDelete channels Setup MenuSetup Menu Deleting Channels from a Quick Channel ListDelete Menu Delete MenuQuick Channels Using Quick Channel ListsSetting up Channel Lists Macro MenuSetting Up Setting Up the SUR-35Macro Timers Choosing a Device Setting Up a New TimerPress OK to confirm timer type Choose DeviceOther Features Other FeaturesUsing Timers New deviceMacros Using MacrosLabeling a Device Naming devicesButton to change to the Touch &1 Changing the Touch Screen LayoutLCD layout Available LCD choices for allPress OK to confirm your changes Programming Programming Infrared CodesDefine Macro Using Pre-programmed Manufacturer Codes Pre-set codesIntroduction to Macros Creating and Using MacrosCreating a Macro Sequence Auto search Controlling the DeviceOperation To use automatic search Automatic SearchSelecting a Device to Control Using the Learning FunctionControlling Devices Changing Touch Screen PagesDeleting devices Learning from Another Remote ControlSelect the device you Wish to delete. Make sure Deleting a Device Deleting a Specific Key Deleting buttonsLearning codes Collecting codes Press and hold the Setup Button on Touch ScreenCollecting Unrecognized Infrared Codes SoftKey
Top Page Image Contents