Sima Products Changing SUR-35 Parameters, Power Down Time Period, Installing Batteries

Page 9

 

Power Down

 

SUR-35 User Manual

 

 

 

 

Chapter 7 – Changing SUR-35

Parameters

Many of the SUR-35 parameters can be changed. This chapter explains the different customizations you can make.

Power Down Time Period

This setting specifies the time delay the SUR-35 will wait until it automatically shuts down. (The touch screen will go blank to conserve battery usage.)

This setting can be changed from 1 to 90 minutes.

1.Press and hold the SETUP button for three seconds.

2.Use the up and down arrows to select PWDN

3.Use the up/down arrows to select a time period ranging from 1 to 90 minutes. Press OK to return to the SETUP menu.Press EXIT to return to the main menu. The unit will power down when the time period expires

Ch.

7

Page

SUR-35 User Manual

 

Batteries

Installing Batteries

The SUR-35 operates on four AAA Alkaline batteries (not included). Batteries must be inserted before you can operate the SUR-35. To insert the batteries, refer to the following illustration:

1.Turn the remote over, push on the tab and lift the cover off.

2.Insert the batteries, matching the batteries to the (+) and (-) marks inside the battery case. Note: Make sure the data switch located in the battery compartment is set to “NORM”.

3.Snap the battery cover back into place.

Figure 3:

Installing Batteries

Low Battery Indicator

When the batteries are low, the battery low icon will be displayed in the upper left-hand corner just above the SETUP button:

Figure 4: The Battery Low Icon

Battery Tips and Precautions

Immediately replace batteries when the battery low icon appears.

The SUR-35 will retain data when batteries are replaced

Always use fresh batteries. Alkaline batteries are recommended. Do not mix different types of batteries.

Be sure that the positive (+) and negative (-) polarities of the batteries match the diagram shown in the compartment.

Do not expose the batteries to excessive heat or flame.

Keep batteries out of the reach of children.

Weak batteries reduce the effective distance of the unit.

To reduce danger of leakage and damage, remove used batteries when used longer than two years.

Ch.

2

Page

52

9

Image 9
Contents Day Limited Warranty WarrantyPreface TroubleshootingAbout this manual CopyrightTable of Contents Creating and Using Macros Appendix C TroubleshootingSUR-35 Features Appendix B AccessoriesAccessories Introducing the SUR-35Specifications Appendix a SpecificationsUnpacking the SUR-35 Identifying ComponentsResetting to Factory Defaults Features OverviewGetting Started Beep TogglingFeatures FeaturesBacklight Time Period BacklightInstalling Batteries Power Down Time PeriodPower Down Changing SUR-35 ParametersDisplaying Version Number Touch ScreenTouch Screen Turning the Touch Screen OnSleep mode Using Sleep ModeRubber Buttons Touch Screen ButtonsUsing Quick Channel Lists Transmitting System SetupMenus Program MenusSetup Menu Setup MenuDelete channels Deleting Channels from a Quick Channel ListDelete Menu Delete MenuSetting up Channel Lists Using Quick Channel ListsQuick Channels Macro MenuSetting Up the SUR-35 Setting UpMacro Timers Press OK to confirm timer type Setting Up a New TimerChoosing a Device Choose DeviceUsing Timers Other FeaturesOther Features New deviceLabeling a Device Using MacrosMacros Naming devicesLCD layout Changing the Touch Screen LayoutButton to change to the Touch &1 Available LCD choices for allPress OK to confirm your changes Programming Infrared Codes ProgrammingDefine Macro Pre-set codes Using Pre-programmed Manufacturer CodesCreating and Using Macros Introduction to MacrosCreating a Macro Sequence Operation Controlling the DeviceAuto search To use automatic search Automatic SearchControlling Devices Using the Learning FunctionSelecting a Device to Control Changing Touch Screen PagesLearning from Another Remote Control Deleting devicesSelect the device you Wish to delete. Make sure Deleting a Device Deleting buttons Deleting a Specific KeyCollecting Unrecognized Infrared Codes Press and hold the Setup Button on Touch ScreenLearning codes Collecting codes SoftKey