Revox M642 HD manual Television mode, PC Mode, Operation with additional devices

Page 47

General operation

Television mode

The display is in standby mode.

. To switch on, press one of the numeric buttons [0...9] or the [TV] button on the remote control.

Then the television channel last selected (programme number) appears on screen.

If the option <SET UP ' DISPLAY SOURCE INFO> is set to ”On”, the following info window for signal source is displayed for approx. 5 seconds

 

If the option <SET UP ⇒ DISPLAY SOURCE

TV - 2 - ZDF

INFO> is set to ”On”, the following info window for

STEREO

signal source is displayed for approx. 5 seconds -

 

see the drawing at the left side.

. Press the [ PY ] or [ PB ] button to increase or reduce the channel number in single increments or enter each channel number directly using the numeric buttons on the remote control.

Teletext

Your display can receive and display TOP/FLOF Teletext information.

. Select a television channel with Teletext.

. Press the [TEXT] button on the remote control to display Teletext or use the numeric buttons to directly select Teletext pages.

The red, green, yellow and blue buttons on the remote control have different functions depending on the type of Teletext. They are displayed at the bottom of the Teletext screen.

ENGLISH

PC Mode

. Switch off the display and the PC.

. Connect your PC and the display using the enclosed video cable (DVI plug on the display and HD-sub connector on the PC).

. Switch ON the display and PC again.

 

 

 

PC (RGB) must be set in under the option <INPUTS /

 

PC (RGB)

PIP SOURCE>. When switched on, the display

 

1024 x 768

automatically detects the picture format set on the PC.

 

 

This information is displayed in an info window - see

 

 

the drawing at the left side.

Operation with additional devices

Video recorder

. Switch OFF the display and video recorder.

There are 3 options for connecting your video recorder to the display:

Dvia the aerial lead; read the operating instructions for your video recorder on this subject D using a SCART cable connected either to SCART1 or SCART2

D if your video recorder has an S-video output, connect this to the Y/C input.

. Switch the display and video recorder back ON.

. o switch over to the connected input (e.g. SCART1) press the [VIDEO] button repeatedly.

DVD player

Operation with Revox M51 and DVS module: see the operating manual DVS module

. Switch OFF the display and DVD player.

. Connect your DVD player via SCART1, YC input or YUV input, if it has an S-video output.

. Switch the display and DVD player back ON.

. To switch over to the connected input, press the [VIDEO] button repeatedly.

ENGLISH

19

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Reception plasma 42 HD Plasma TV M642 HD 2950-4042-C288 Rev.00 Alltägliche Bedienung SicherheitshinweiseÜbersicht Erste InbetriebnahmeWichtige Grundregeln zum Gebrauch SicherheitshinweiseReinigung des Gehäuses EntsorgungReinigung Reinigung des Plasma-TV’sBatterien KonformitätBei Störungen Ausstattung ÜbersichtLieferumfang Anschlüsse Bedientasten am Gerät Ortsbedienung Bedientasten und Funktionen der FernbedienungBlickrichtung Auspacken, Blickrichtung, Aufstellungsort und InstallationErste Inbetriebnahme AuspackenTischaufstellungWandmontage AufstellenWandmontage Satelliten-Receiver Anschließen und EinschaltenAnschliessen Kabelanschluss / Terrestrische AntenneEinstellungen vornehmen OSD-Menü BedienungVorbereitung EinschaltenEinstellungen bei erster Inbetriebnahme Grundeinstellungen OSD-Menü On Screen DisplaySecam L PAL BGPAL PAL DKAktuelles Programm löschen Menu Löschen beenden PC BetriebBenutzerformate einstellen Auto Abgleich FunktionUmschalten Alltägliche BedienungTon einstellen AusschaltenBild einstellen Bildformat Anti-FlickerBetrieb mit zusätzlichen Geräten FernsehbetriebPC Betrieb Farbtemperatur SonderfunktionenManuelle Programmsuche StandbildMulti-PIP Funktion Unterstützung des Hdtv Standards Automatisches abschaltenZweikanalton umschalten DekoderbetriebMenü Info BildschirmschonerEinstellung ⇒ Aufrufen Werkseinstellungen FehlerbehebungFehler Mögliche Ursache Mögliche Behebung Stellungen ⇒ Auto AbgleichTechnische Daten Page Table of Contents Important basic principles for use Safety instructionsWaste disposal CleaningCleaning the plasma TV Cleaning the casingBatteries Event of any faultsConformity Scope of supply OverviewAntenna Connection socketsLine OUT L/R Must only use 2 LR03 AAA 1.5 V batteries Control buttons and functions of the remote controlControl buttons on the display unit Local operator control Viewing position Unpacking, viewing, locating and installingGetting started UnpackingWall mounting InstallationVideo recorder / DVD player / satellite receiver Connecting and switching on the displayConnecting the display Cable connection / terrestrial aerialPreparations Using the OSD menuSwitching on the display Configuring settingsSettings for getting started Basic OSD menu settingsKika CNN Select a programme Current = 1 ARD Selecting PC modeSetting user formats Auto setup functionRegulating the sound General operationAdjusting the picture Zoom Picture formatThis option is displayed only if Userzoom is set underOperation with additional devices Television modePC Mode Manual channel search Color temperaturePIP Mode Special functionsMulti-PIP function Setting PIPPuts / PIP ⇒ Main Input PC RGB Setting Split Screen Support of the Hdtv standard Automatic switch-offSwitching over to dual sound Decoder modeMenu Info Screen saverMake sure sufficient ventilation is provided TroubleshootingFaults Possible Causes Possible Solution SET UP ⇒ Reset to Factory DefaultsTechnicalspecifiications Germany Zentralservice
Top Page Image Contents