Revox M642 HD manual Connecting and switching on the display, Connecting the display, DVD player

Page 38

Getting started

Connecting and switching on the display

Connecting the display

(for an overview of the connection sockets see the illustration on page 6)

. Plug the mains power cord into the mains input jack on the plasma TV and the mains plug into a plug receptacle.

Cable connection / terrestrial aerial

If you would like to connect a cable, a terrestrial aerial or a satellite recei- ver, use the ANTENNA socket for this purpose.

Video recorder / DVD player / satellite receiver

If you receive your TV channels via satellite, connect your receiver by means of a SCART cable to the SCART 1 or SCART 2 socket.

In addition, SCART 1 has a connection socket for RGB sources, e.g. a DVD player.

Only a SCART 2 can be used for connecting a decoder.

DVD player

For connection of a DVD player or another video source to a YUV-output please use the display’s YUV-input.

If your DVD player has a DVI-I output port, you can use the DVI-I input port and the audio input port LINE IN PC on the display screen.

f a DVD player is connected to the DVI-I input port of the dis- play screen, the following must be ensured:

D Before you make a connection between the DVD player and the display screen using the cables, you must disconnect

the mains plug of the DVD player from the plug socket.

D Once the cables are plugged in on the DVD player and on the display screen, the mains plug of the DVD player can be reconnected to the mains.

If you do not comply with this procedure, damage can be caused to the DVD player or to the display screen!

Notice : If your DVD player has a HDMI interface, you use to the connec- tion the supplied adapter cable ”HDMI on DVI”.

PC

Use the PC DVI-I socket to connect your PC to the display. If your PC has an analogue VGA output port, use the DVI-I connecting cable supplied on a 15 Pin HD-Sub to connect it.

On older PC graphic cards it is possible that pin 9 is barred.

Should this be the case, please contact the service hotline.

10

ENGLISH

Image 38

Contents Reception plasma 42 HD Plasma TV M642 HD 2950-4042-C288 Rev.00 Erste Inbetriebnahme SicherheitshinweiseÜbersicht Alltägliche BedienungSicherheitshinweise Wichtige Grundregeln zum GebrauchReinigung des Plasma-TV’s EntsorgungReinigung Reinigung des GehäusesBatterien KonformitätBei Störungen Ausstattung ÜbersichtLieferumfang Anschlüsse Bedientasten und Funktionen der Fernbedienung Bedientasten am Gerät OrtsbedienungAuspacken Auspacken, Blickrichtung, Aufstellungsort und InstallationErste Inbetriebnahme BlickrichtungTischaufstellungWandmontage AufstellenWandmontage Kabelanschluss / Terrestrische Antenne Anschließen und EinschaltenAnschliessen Satelliten-ReceiverEinschalten OSD-Menü BedienungVorbereitung Einstellungen vornehmenGrundeinstellungen OSD-Menü On Screen Display Einstellungen bei erster InbetriebnahmePAL DK PAL BGPAL Secam LPC Betrieb Aktuelles Programm löschen Menu Löschen beendenAuto Abgleich Funktion Benutzerformate einstellenAusschalten Alltägliche BedienungTon einstellen UmschaltenBild einstellen Anti-Flicker BildformatBetrieb mit zusätzlichen Geräten FernsehbetriebPC Betrieb Standbild SonderfunktionenManuelle Programmsuche FarbtemperaturMulti-PIP Funktion Dekoderbetrieb Automatisches abschaltenZweikanalton umschalten Unterstützung des Hdtv StandardsBildschirmschoner Menü InfoStellungen ⇒ Auto Abgleich FehlerbehebungFehler Mögliche Ursache Mögliche Behebung Einstellung ⇒ Aufrufen WerkseinstellungenTechnische Daten Page Table of Contents Safety instructions Important basic principles for useCleaning the casing CleaningCleaning the plasma TV Waste disposalBatteries Event of any faultsConformity Overview Scope of supplyAntenna Connection socketsLine OUT L/R Must only use 2 LR03 AAA 1.5 V batteries Control buttons and functions of the remote controlControl buttons on the display unit Local operator control Unpacking Unpacking, viewing, locating and installingGetting started Viewing positionInstallation Wall mountingCable connection / terrestrial aerial Connecting and switching on the displayConnecting the display Video recorder / DVD player / satellite receiverConfiguring settings Using the OSD menuSwitching on the display PreparationsBasic OSD menu settings Settings for getting startedKika CNN Selecting PC mode Select a programme Current = 1 ARDAuto setup function Setting user formatsGeneral operation Regulating the soundAdjusting the picture Userzoom is set under Picture formatThis option is displayed only if ZoomOperation with additional devices Television modePC Mode Special functions Color temperaturePIP Mode Manual channel searchMulti-PIP function Setting PIPPuts / PIP ⇒ Main Input PC RGB Setting Split Screen Decoder mode Automatic switch-offSwitching over to dual sound Support of the Hdtv standardScreen saver Menu InfoSET UP ⇒ Reset to Factory Defaults TroubleshootingFaults Possible Causes Possible Solution Make sure sufficient ventilation is providedTechnicalspecifiications Zentralservice Germany