3M 2273M-iD, 2250M manual Configuring The Receiver, Select Depth Units, Setting the Receiver Clock

Page 18

5. Configuring The Receiver

In the setup mode, the units of depth measurement, time, date, and date format can be set. The receiver can be configured to detect only certain frequencies and/or specific utility markers (3M™ Dynatel™ Receivers 2250M-iD and 2273M-iD only). User defined frequencies can be programmed, language of the receiver can be selected, and tone frequencies set.

A. Select Depth Units

MENU [6] + >>More [SK:4] + Setup [SK:6] + Units [SKToggle:6a]

1.Press Units [SK toggle:6a].

2.The soft key command will toggle between inches (in), centimeters (cm), and feet/inches (ft-in).

3.Press Locate/OK [5].

B. Setting the Receiver Clock

Set the time, date, and date format of the receiver. Depth and Current measurements are time and date stamped, as well as read write marker information (iD units only).

MENU [6] + >>More [SK:4] + Setup [SK:6] + Clock [SK:6b]

1.Press the left/right arrow [SK] to highlight the digit of the date or time to change.

2.Press the + or - [SK] to increment or decrement.

3.When the date format is highlighted, the format will toggle between mm/dd/yy and dd/mm/yy.

4.Press Locate/OK [5] to save, or Menu [6] to cancel.

C. Selecting a Language

MENU [6] + >>More [SK:4] + Setup [SK:6] + Lang [SKToggle:6c]

The soft key command will cycle through available languages. Press Locate/OK [5]. Alternate languages can be uploaded to the receiver using the 3M™ Dynatel™ PCTools Software. The 3M™ Dynatel™ PC Tool Kit Software is available free of charge at www.3M.com/dynatel under the Software section; 2550/2573/2250M/2273M/1420 Locator PC Tools xx.x.x (EXE xx.xMB).

18	78-8130-6150-0 Rev G

Image 18

Contents 3M Dynatel Contents Rev G Rev G Rev G Safety Information Intended UseAbout This Manual Transmitter Battery Installation Quick StartReceiver Battery Installation Cleaning Service and Accessories3M Dynatel Transmitter 2273 Keypad and Connector Definitions Rechargeable Battery Maximum Transmitter Output3M Dynatel Receiver 2250M Key Pad and Display Definitions Dynatel3M Dynatel Receiver 2273M Key Pad and Display Definitions Menu Displays Main MenuRev G Rev G Select Depth Units Configuring The ReceiverSetting the Receiver Clock Selecting a LanguageMenu 6 + More SK4 + Setup SK6 + More SK6d + Tone Freq SK6j Enabling/Disabling FrequenciesCreating User Defined Frequencies Filtering Power Frequency Interference Selecting Locating AudioBuried Cables And Pipes Transmitter Connections Direct Connect MethodRev G Dyna-Coupler Method Non-Sweeping Passive Induction Mode Locating Induction MethodSweeping Active Induction Mode Locating Passive SweepsOne-person Active Induction Mode Sweeps Two-person Active Induction Mode Sweeps Transmitter Set-upReceiver Modes Locate/OK 5 + Cable/Pipe SK + Mode SK + Dir Pk SK ToggleLocate/OK 5 + Cable/Pipe SK + Mode SK + DirNull SK Toggle Directional Peak Dir PkLocate/OK 5 + Cable/Pipe SK + Mode SK + Spl Pk SK Toggle Special Peak Spl PkDepth and Current Estimate Expanded ModeLocate/OK 5 + Cable/Pipe SK + Mode SK + Ind Pk SK Toggle Induction Peak Ind PkLocating Frequencies Active FrequenciesPower Frequencies Passive FrequenciesAuxiliary Frequencies Locating in Directional Peak Mode Rev G Locating Active Duct Probes Sondes Determining ADP DepthLocating Buried Sheath Faults and Earth Return Faults Transmitter SetupPinpointing the Buried Fault Green Band Alert Mode Locating 3M Electronic Markers 3M iD MarkersEnabling/Disabling Marker Types Single Marker Locate Press Locate/OKDual Marker Locate 3M iD Marker DepthPassive 3M Electronic Marker Non-iD Depth Creating/Editing Templates for 3M iD Markers Creating New TemplatesMenu 6 + Data/Templat SK2 + User Templat SK2c Rev G Editing Templates Menu 6 + Write Mode SK1 Writing 3M iD MarkersPress Start Write SK Press Menu 6 + Write Mode SK1 Modifying Marker Data to be WrittenRev G Reading 3M iD Markers Reviewing Marker Read/Write History Read HistoryMenu 6 + Data/Templat SK2 + Read History SK2a Write History SK Capturing the GPS Coordinates Capture Mode / ModeGPS Operation Communicating with the GPS DeviceMenu 6 + COM Setup SK3 + GIS Path Mapping with GPSCreating Trace Templates Menu 6 + Com SK3 + GIS SK or PDA SKAerial Faults Toning Additional ApplicationsConnection Diagrams Cable IdentificationHelp Mode Menu 6 + More SK4 + Help SK8Self Test Of Receiver Menu 6 + More SK4 + Self Test SK7Product Description Product Description And Optional AccessoriesStandard Configurations Direct Connect Cables Earth Contact FrameOptional 3M Accessories for 3M Dynatel Locators Receiver Specifications SpecificationDetection Depth 3M Non-iD Passive Transmitter Specifications Mode can display a fault resistance up to 10M ΩEnvironmental and Regulatory Specifications Rechargeable Battery InformationRev G Electrical Markets Division Important Notice